PROAIM Curve-120 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Assembly Manual
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Curve-120 Curved Camera Slider with Moon
Control System (SL-CUR-120-MC)
Camera Slider
2 x End Feet and
1 x Centre feet
1/4”Camera Bolt
2 x Knob
Camera Plate
Bag & Strap
1 x Allen key-3/16”
Plasc screw driver
Combo-1

2
Curved Camera slider with End feet Setup
• Loosen the knobs of the end feet and open
them.
• Aer opening the feet, secure them by
re-ghtening with the provided knobs. Follow
the same process for all the sets of feet.
NOTE: Aach the center feet to the center part
of the slider only.
• Remove all the bolts of the Camera Slider from
both the sides with the help of an Allen Key, as
shown in the image.
• Remove the center bolts of the camera slider
with the help of an Allen key.
Camera Plate
with Motor
12v adapter
3 x Allen key
(3/16”, 2.5mm,1.5mm)
Grub screw
Universal
Adapter
1/4” Camera Bolt, BS-100
Remote Controller
+ Strap
3mtr Wire
Stopper
Combo-2

3
• Place the middle feet at the center of the
slider and then insert bolts, by matching the
threads of the slider and the middle feet. Then
ghten with an Allen key to secure.
• Follow the same process to aach the other
set of end feet.
• Insert the stopper, by matching the threads of
the end feet and ghten properly.
• Finally all the feet have been aached to the
slider.
• Follow the same process to insert the other
stopper in the 2nd set of end feet .
NOTE: All sets of feet have threads for stoppers
except for the center feet. The two end feet
stoppers provide support to the camera plate.
• Place the end feet on the slider and then
insert bolts, by matching the threads of the
slider and the feet. Then ghten with an Allen
key to secure.

4
• Loosen the side knobs of the camera plate and
aach it on the slider. Then, re-ghten the
side knobs.
Proaim Curve-120 curved camera slider with Moon Control System.
• Properly insert the camera bolt into the
camera plate.
• Another addional stopper is included to
secure the camera (Not Included) properly.

5
• Open the motor lever by pulling it, as shown in
the image.
• Then secure it with the help of a screwdriver,
as shown in the image.
• Aach the Camera Plate with Motor to the
boom of the camera (Not Included).
• Aach the camera plate by aligning its threads
to the camera and then secure it using the
screw driver (Not Included) .
• Then place the camera (Not Included) on the
slider & properly ghten the knob of the
camera plate.
• The camera (Not Included) is now properly
mounted on the slider, as shown in the
picture.
Camera Plate with Motor

6
• Aach the other end of the 3 meter wire
(4 pin hero push pull connector) to the 4 pin
male connector on controller.
• Aach one end of the 12v adapter cable to the
adapter.
• Then connect the other end of the cable with
the baery.
• Then place the camera (Not Included) on the
slider & properly ghten the knob of the
camera plate.
• Then aach the motor by connecng it
properly to the slider. Thus, powering the
slider.
Cauon: While performing this step, make sure
that your camera plate is mounted onto the
slider.
• Aach the Female connector of the motor to
one end of the 3 meter wire of DC male
connector.
Power the Remote Controller with 2 ways
1. 12v Adapter

7
Remote Controlled Movement Funcons
• Connect the electric plug of the 12v adapter
wire to the universal adapter for generang
the power-supply.
• 12v Adapter: Aach the 12v Adapter with
the controller and press the power buon.
• Baery: Aach the baery (Not Included) with
the controller and press the power buon.
2. Baery

8
YOUR PROAIM CURVE-120 CURVED CAMERA SLIDER WITH
MOTION CONTROL SYSTEM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.