Qlight STA35SL Series User manual

STA35 SL SERIES
Thank you for purchasing Q.Light product. Please read this manual
carefully before installing this product for safe and long use.
▪High visibility by employing special dispersing lens.
▪Convenient installation by adopting screw type structure at
bottom side of body.
▪LED Steady type (supporting flashing type by external control)
▪Protection Class : IP44
1) STA35SL
▪General Specification
Model
Layer
Voltage
Current
Weight
Color
STA35SL
1
AC/DC12V
0.16A
0.35Kg
Red-R
AC/DC24V
0.08A
0.35Kg
AC110V
0.02A
0.35Kg
AC220V
0.02A
0.35Kg
2
AC/DC12V
0.32A
0.35Kg
Red-R
Green-G
AC/DC24V
0.16A
0.35Kg
AC110V
0.04A
0.35Kg
AC220V
0.04A
0.35Kg
3
AC/DC12V
0.48A
0.41Kg
Red-R
Amber-A
Green-G
AC/DC24V
0.24A
0.41Kg
AC110V
0.06A
0.41Kg
AC220V
0.06A
0.41Kg
4
AC/DC12V
0.64A
0.47Kg
Red-R
Amber-A
Green-G
Blue-B
AC/DC24V
0.32A
0.47Kg
AC110V
0.08A
0.47Kg
AC220V
0.08A
0.47Kg
5
AC/DC12V
0.8A
0.53Kg
Red-R
Amber-A
Green-G
Blue-B
White-w
AC/DC24V
0.4A
0.53Kg
AC110V
0.1A
0.53Kg
AC220V
0.1A
0.53Kg
* Current and contact capacity (by 1 layer)
VLOTAGE
Current
(Signal)
Inrush current
External
contact
Current
(Buzzer)
AC/DC12V
0.16A
Abt.4.8A
Over 5A
0.015A
AC/DC24V
0.08A
Abt.2.4A
Over 3A
0.028A
AC110V
0.2A
Abt.0.6A
Over 1A
0.021A
AC220V
0.2A
Abt.0.4A
Over 1A
0.038A
■Outline drawing of STA35SL Series
This product has separate power and signal cable. Please make
sure to connect each cable in accordance with below connection
diagram.
■DC, AC Steady type (involving built-in buzzer type)
▪Signal cable(Power cable) : UL1007-NO.22(0.3sq) 400mm
▸AC / DC Steady type
OPERATING MANUAL
LED Steady Tower Lamp
Cable connection

▪This product is designed for indoor use. Do not use them
outdoor.
▪Mount them vertical and upright where there is low vibration
and shock if possible.
▪Drill the suitable holes at place where you want to install in
reference with below table.
▪Fix the product by using nuts (M20*2.5) on bottom of the
product.
Model
Hole size
STA35SL Series
Ø10
▪Make sure end of any unused wires are insulated by tape. A
short circuit of signal line can cause a trouble.
▪If using voltage is seriously higher or lower than rated voltage,
it can reduce the self-life of the product or can cause a
problem on product operating. Make sure the using voltage
does not exceed +/-5% of the rated voltage.
▪If lens or body of the product is contaminated by chemicals
such as thinner, benzene, the product can be damaged,
discolored or deformed. Please be careful.
▪Do not make any impact onto product. It causes short curicut
or trouble.
▪Do not strongly pull the wire out from the product. It can
cause a disorder.
Situation
Main reason
Solution
Non- Lighting Partly
LED is partly damaged,
supplying higher
voltage than rated
voltage.
Check the working
Voltage
Feeble Lighting
Supplying Voltage
Lower Than Rated
Voltage
Check the working
Voltage
No light
No Wiring
Check the wiring.
No power source
Check the power supply
Installation
Trouble Shooting