Teknik Hampstead Park 5420834 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Hampstead Park TV Stand/Credenza
Model 5420834
Your holder for all
things awesome.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Use of a TV that is too heavy or lare is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too lare for the available space miht be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weiht of your TV. Compare it to the diaram below – before you begin assembly!
• This Sauder unit is desined for use with flat panel televisions weihin less than 95 pounds. Never use with a TV that weihs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diaram.
• Never place the front ede of the TV past the front ede of the TV support shelf (or stop moldin – if equipped)
• Never allow the sides of the TV to extend past the side edes of the TV support surface.
• Be sure to apply the warnin label as instructed later in the assembly. The label provides important safety related information.
3
4
5-21
22-24
25-27
28-30
31
Table of Contents
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Assembly Tools Required
95 lbs.95 lbs.
71"71"
19"19"
WARNING
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A2
B2
C2
C2
D
D
E2
F
G3
H
I
J
K
L
M
N2
N2
O
O
O
D115
D723
D13
D12
Pae 3
Now you know
our ABCs.
M67
A2 RIGHT END (1)
B2 LEFT END (1)
C2 UPRIGHT (2)
D LOWER UPRIGHT (2)
D12 RIGHT DRAWER SIDE (3)
D13 LEFT DRAWER SIDE (3)
D115 DRAWER BACK (3)
D723 DRAWER BOTTOM (3)
E2 TOP (1)
F BOTTOM (1)
G3 SHELF (1)
H BACK (1)
I BRACE (1)
J DRAWER FRONT (1)
K RIGHT DRAWER FRONT (1)
L LEFT DRAWER FRONT (1)
M BASE (1)
M67 DRAWER BRACE (3)
(Hidden part usin recycled
material. Color may vary.)
N2 SIDE BASE (2)
O MOLDING (9)

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
35GA CABINET RIGHT - 3 35GB CABINET LEFT - 3 35GC DRAWER RIGHT - 3 35GD DRAWER LEFT - 3
1F HIDDEN CAM - 15 2F CAM DOWEL - 15 10F TWIST-LOCK®FASTENER - 8
10A SLIDE CAM - 6
31G CORNER BRACKET - 4
1N NAIL - 42 13P CAM COVER - 4
2S BLACK 1-7/8" FLAT HEAD SCREW - 8
12S BROWN 1" FLAT HEAD SCREW - 36
1S BLACK 9/16" LARGE HEAD SCREW - 38
Pae 4
30S BLACK 1-9/16" FLAT HEAD SCREW - 15
29M BUMPER CARD - 2
4G METAL BRACKET - 4
3S GOLD 5/16" FLAT HEAD SCREW - 24
PULL - 3
154K
(Refer to step 16 for proper
location and application)
WARNING LABEL - 1
3L
WARNING
For use with televisions weighing 95 lbs.
(43 kg) or less. Use with heavier
televisions may result in instability causing
tip over resulting in death or serious injury.
-Never allow children to climb on audio/
video furniture.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
11/18 2 6 9 2 2 7 269227

Step 1
10F
(8 used)
A2
B2
Do not tihten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratchin your unit or the floor.
å To bein assembly, push a SAUDER TWIST-LOCK® FASTENER (10F)
into the lare holes in the ENDS (A2 and B2).
å Repeat this step for the SHELF (G3).
Pae 5
Some assembly
(and snacks) required.
Meet Parts (A2 and B2). These
components have been enineered to
be lihter, stroner, faster… well ok. Not
technically faster. But definitely makes for a
sturdier Credenza that’s easier to assemble
and friendlier to the environment.

å Push fifteen HIDDEN CAMS (1F) into the UPRIGHTS (C2
and D), BOTTOM (F), and DRAWER BRACES (M67). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Step 2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
(15 used)
Arrow
1F
2F
Arrow
1F
2F
C2
C2
D
D
F
Pae 6
M67
M67
M67

Step 3
å Fasten a CABINET RIGHT (35GA) to the RIGHT END (A2)
and a CABINET LEFT (35GB) to the LEFT END (B2). Use
four GOLD 5/16" FLAT HEAD SCREWS (3S) throuh
holes #1 and #3.
1
2
3
Surface with
TWIST-LOCK
®
FASTENERS
Surface with
TWIST-LOCK
®
FASTENERS
B2
A2
Roller end
Roller end
1
2
3
Pae 7
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S

Step 4
å Fasten the CABINET RIGHTS (35GA) and CABINET
LEFTS (35GB) to the LOWER UPRIGHTS (D). Use
eiht GOLD 5/16" FLAT HEAD SCREWS (3S) throuh
holes #1 and #3.
Finished ede
Finished ede
Roller end
Roller end
Roller end
Roller end
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
D
D
1
2
3
1
2
3
1
2
3
1
2
3
Pae 8
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S

Step 5
å Fasten the UPRIGHTS (C2) to the TOP (E2). Tihten four
HIDDEN CAMS.
Start Tighten
Arrow
Minimum
190 derees
Maximum
210 derees
Arrow
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Pae 9
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with holes
C2
C2
E2
These edes
must be even.
Part (E2). Another sturdier,
easier, friendlier component.
This hole is closer
to this ede.

å Fasten the SHELF (G3) to the UPRIGHTS (C2). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 6
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
Surface with
TWIST-LOCK
®
FASTENERS
C2
C2
G3
Pae 10
These edes
must be even.