Teknik Barrister Home 4 Drawer Chest User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Barrister Home 4 Drawer Chest
Barrister Home Collection | Model 5418706
www.teknikoffice.co.uk
The dresser's
not-so-distant cousin.
Teknik

Table of Contents Assembly Tools Required
3
4
5-22
31
Part Identification
Hardware Identification
Assembly Steps
418706 www.sauder.com/servicesPae 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E BACK (1)
F BRACE (3)
G BASE (1)
I RIGHT BASE (1)
J LEFT BASE (1)
K UPPER DRAWER FRONT (1)
L DRAWER FRONT (3)
M FRONT MOLDING (1)
N RIGHT MOLDING (1)
O LEFT MOLDING (1)
P BACK RAIL (1)
R SIDE RAIL (2)
D22 DRAWER RIGHT SIDE (3)
D23 DRAWER LEFT SIDE (3)
D26 SMALL DRAWER RIGHT SIDE (1)
D27 SMALL DRAWER LEFT SIDE (1)
D182 SMALL DRAWER BACK (1)
D183 DRAWER BACK (3)
D987 DRAWER BOTTOM (4)
M64 DRAWER BRACE (4)
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.

Part Identification Now you know
our ABCs.
Pae 3
A
B
C
D
E
F
G
I
J
K
L
M
N
O
P
R
F
F
R
D987
M64
D27
D26
D182
D987
M64
D23
D22
D183

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
5L WARNING LABEL - 1
(Refer to Step 16 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M
SAFETY DRYWALL
ANCHOR - 1
61M
35AA UNIVERSAL CABINET RAIL - 8 35AC DRAWER RIGHT - 4 35AD DRAWER LEFT - 4
WASHER - 1
13M
METAL BRACKET - 7
4G
METAL PIN - 6
1R
MOLDING
CONNECTOR - 2
19F
10A SLIDE CAM - 8
NAIL - 36
1N
HIDDEN CAM - 18
1F CAM DOWEL - 18 2F
PULL - 6
70K KNOB - 4
71K
Pae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 15
1S
SILVER 1-1/8" FLAT HEAD SCREW - 7
10S
BLACK 1-1/4" FLAT HEAD SCREW - 4
7S
BLACK 7/8" MACHINE SCREW - 16
37S
BROWN 1-1/2" FLAT HEAD SCREW - 7
14S
3S GOLD 5/16" FLAT HEAD SCREW - 32
30S BLACK 1-9/16" FLAT HEAD SCREW - 20
Pae 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push eihteen HIDDEN CAMS (1F) into the ENDS (A and B),
BOTTOM (D), BRACES (F), and DRAWER BRACES (M64).
Then, insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Pae 6
Arrow
1F
2F
(18 used)
Arrow
1F
2F
Do not tihten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
D
F
F
F
M64
M64 M64
M64

StepStep 2
Pae 7
å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the
ENDS (A and B). Use sixteen GOLD 5/16" FLAT HEAD
SCREWS (3S) throuh holes #1 and #3.
å *patent pendin lide system
GOLD 5/16" FLAT HEAD SCREW
(16 used in this step)
3S
3
2
1
1
2
3
A
1
2
31
2
3
3
2
13
2
1
Finished ede
Surface with
HIDDEN CAMS
B
Surface with
HIDDEN CAMS
Finished ede
Remember:
Rihty tihty.
Lefty loosey.
Glide end
Glide end
3
2
1
1
2
3

Step
å Fasten the TOP (C) to the RAILS (P and R). Use seven
BROWN 1-1/2" FLAT HEAD SCREWS (14S).
Step 3
Pae 8
BROWN 1-1/2" FLAT HEAD SCREW
(7 used in this step)
14S
P
R
R
C
Curved ede
Surface with fewer holes

StepStep 4
Pae 9
å Tap two MOLDING CONNECTORS (19F) into the notches
in the MOLDINGS (M, N, and O).
Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS.
Flat end
Flat end
19F
N
O
M
19F
Unfinished surface
Unfinished surface
Unfinished surface

StepStep 5
Pae 10
å Fasten the TOP (C) to the MOLDINGS (M, N, and O). Use
seven SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å NOTE: Do not overtihten the SCREWS into the TOP.
N
O
C
M
Finished surface
Finished surface
Surface with
more holes
Finished surface
SILVER 1-1/8" FLAT HEAD SCREW
(7 used in this step)
10S
Do not overtihten
the SCREWS (10S).
Lon curved ede