Yealink MeetingEye 600 User manual

Yealink MeetingEye 600 Video Conferencing Endpoint Quick Start Guide
V1.0
Yealink Network Technology CO., LTD
English | 皍⡤⚥俒

1
Package Contents
3m
Ethernet CableAAA Battery×2MeetingEye600
VCR20
Remote Control
1.8m
HDMI Cable
(for the display device)
Cable Tie×5 Quick Start Guide
We recommend that you use the accessories provided or approved by Yealink. The use of
unapproved third-party accessories may result in reduced performance.
Use the Yealink original power adapter (48V/0.7A) to charge the endpoint only. The use of the
third-party power adapter may cause the damage to the endpoint.
Put the magnet rings on the HDMI cable to prevent electromagnetic interference.
Endpoint Installation .PVOUJOH#SBDLFUBOE"DDFTTPSJFT1PXFS"EBQUFS1. Placing MeetingEye 600
Mount the MeetingEye 600 below the TV when
the mounting height of the TV is higher than
120cm.
Mount the camera above the TV when
the mounting height of the TV is lower
than 120cm.
$51
Optional Accessories
8118JSFMFTT1SFTFOUBUJPO1PE
TV
TV
#MVFUPPUI8JSFMFTT.JDSPQIPOFT#5#MVFUPPUI64#%POHMFWireless Sharing PackageTouch Panel Package .JDSPQIPOFPackage

2
Hole depth: 30mm
Hole diameter: 6mm
T4×30 screws
2. Wall Mounting
Use the bracket to mount your endpoint on a wall. The mounting height affects your camera view.
The recommended height is 1.6m above the ground.
SS
3
4
5

3
Endpoint Connections
1.8m
HDMI
Cable
3m Ethernet Cable
Display
Power Adapter
3. Adjusting the Camera Tilt
For more information on WPP20 wireless
presentation pod, refer to Y
ealink WPP20
Wireless Presentation Pod Quick Start
Guide.
5IF64#1PSU3BUJOH7%$N"PC
Wireless Sharing
WPP20
Wireless Presentation Pod
15°
15°
):6

4
Network Environment
Bandwidth Requirements
Both downlink bandwidth and uplink bandwidth should meet above requirements.
The bandwidth mentioned above is based on a two-way call. Bandwidth in head office should be
increased along with the growing number of connected branch offices.
Network Deployment
Choose Cloud deployment or traditional deployment according to your need.
Cloud Deployment
Cloud deployment does not need complex network settings.You only need to get account information
from your system administrator, and log into the video conference platform.
Do the following to log into the video conference platform via remote control:
1. Select More->Login->Advanced (Default Admin Password:0000)->Video Conference Platform.
2. Enable Cloud Account.
3. Select the desired platform from the pull-down list of Platform Type.
4. Configure the desired platform and log in.
Video Resolution Recommended Bandwidth
Full HD 4K30/1080P60 4Mb
People 1080P60+Content 1080P60 4Mb
Remote Control Cable Ties Installation

5
Configure a Static IP
The following introduces how to use the remote control to configure a static IPv4 address:
1. Select More->Setting->Network->Wired Network (Default Admin Password:0000).
2. Select IPv4 from the pull-down list of IP Mode.
3. Select IPv4, and then press OK key.
4. Disable DHCP.
5. Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.
6. Save the change.
The screen prompts “Reboot now?”
.
7. Select
OK to reboot the endpoint .
Configure Port Mapping
If you deploy the endpoint in an Intranet, you must forward the following ports to the public network on
the firewall, so that your endpoint can receive a public-to-private call.
Port
Function
H.323 signal port
SIPoptional Audio & Video media stream port
Web management portoptional Protocol Type
UDP/TCP
5060-5061
443
50000-51000
1719-1720
TCP/UDP
TCP/UDP
TCP
When you use intelligent traversal to deploy your endpoint, you have to open following ports on
your firewall if they are restricted.
It is recommended that you forward the web management port(443/TCP) to the public network,
so that other office can remotely manage the office.
PortFunction
H.323 signal port
SIPoptional Audio & Video media stream port
Protocol Type
UDP/TCP
TCP/UDP
TCP/UDP
50000-51000
5060-5061
1719-1720
Do one of the following to deploy the endpoint:
Option1: Assign a static public IP address to your endpoint.
Option2: If you deploy the endpoint in an Intranet (behind the firewall), assign a static private IP
address to it and do port mapping on the firewall.
Option3: Deploy the endpoint using intelligent traversal. You only need to assign a private IP
address to your endpoint. Make sure this private IP address can access the public network.
Only outbound calls are available when using this method.
Traditional Deployment

6
Troubleshooting
Connectivity Testing
After installation and deployment, you can test the endpoint by dialing the Yealink Demo Room
(117.28.251.50 or 117.28.234.45 ). If you can’t dial out successfully, please contact your IT
administrator to check the network.
Configuring Static NAT
If you do not use Cloud platform and deploy your endpoint in an Intranet, you have configured port
mapping on the firewall or gateway, but you find that local endpoint appears black screen and you
cannot hear sound when you call Yealink Demo or other endpoints. The most likely reason is that the
firewall or gateway in your environment does not support the ALG feature. In this situation, please take
the following actions so that the static NAT feature on the endpoint can solve this problem.
To configure static NAT via the remote control:
1. Select More->Network->Wired Network (Default Admin Password:0000)->NAT/Firewall.
2. Select Automatic from the pull-down list of Type, the endpoint will obtain public IP address
automatically.
3. If the endpoint does not obtain a public IP address automatically, select Manual Settings from the
pull-down list of Type, and then enter the public IP address in the Public IP Address field.
4. Save the change.

⺫鄳幡⽀7$3黔䱽㐼〿歏寑YMeetingEye 600⚺劼碛緸絁勲絁䌄Y碛)%.*絁欽✵䱹儑爙霃㢊姼⚹"紩❡ㅷկ㖈欰崞梠㞯⚥霪❡ㅷ〳腊⠔鸣䧭偽絁歏䎁䪓կ㖈鵯猫䞔ⲃ♴〳腊꨽銳欽䨪㼆䎁䪓ꅷ》ⴗ㹊〳遤涸䲃倶կ䧮⟌䲀虛⢪欽歋:FBMJOL䲿⣘䧴絑:FBMJOL雩〳涸ꂁ⟝ㄤ絁綈⢪欽劢絑雩〳涸痦♲倰ꂁ⟝ㄤ絁綈〳腊⠔㼋荝䚍腊涸♴꣭կ⢪欽)%.*絁⵸霼㤛♳煂梠欽✵䫒歏煂䎁䪓կ㸝鄳絊畮7.FFUJOH&ZF䘯鸟Ⰶ꡶䭷⽂.FFUJOH&ZF剒⢕鿈縭㹊騨倰呩佅卹ꂁ⟝欽✵㸝鄳⚺劼歏彂鷓ꂁ㐼佞縨.FFUJOH&ZF䔲歏錠䭱涸넞䏞넞✵DN傞絊畮㸝鄳㖈歏錠♴倰կ䔲歏錠䭱涸넞䏞⡛✵DN傞絊畮㸝鄳㖈歏錠♴倰կ
TV
TV
覰暅偽絁띌64#覰暅霃㢊#5$18#5覰暅偽絁띌⯘굥㤛⟝$51ޗিૼࡶ׬ў
811偽絁⠛㾓⸔䩛ઇݏٵߡ׬ў
〳鷥ꂁ⟝

8轠⚏錞呔5䩧㶰湬䖈NN䩧㶰帿䏞NN㟖鄳3
4
5
轠⚏錞呔5
SS

9
鵶䱹絊畮碛緸絁靈侮⧫俷錭䏞碛)%.*絁歏彂鷓ꂁ㐼15°
15°
Display
$51