aivituvin AIR 52 User manual

I
AIR 52
www.aivituvin.com
NSTRUCTION
MANUAL

Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure
every 90 days.
Fasten screws loosely during initial assembly. Do not
fully tighten screws until the item is completely
assembled.
Do not use or store this item in the proximity of open
flame or flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop
using this product until repairs are made and/or factory
replacement parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’s instructions as this could void the
product warranty.
Please retain these instructions for future
NOTICE
01

02
PHILLIPS
SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY
M6.0x80 mm BOLT
12PCS+1 spare
M6.0x70 mm BOLT
48PCS+1 spare
M4.0x60 mm SCREW
27PCS+1 spare
M3.5x50 mm SCREW
20PCS+1 spare
TOOLS REQUIRED
HARDWARE
P1 P2
P3 P4
P5 P6
M3.5x40 mm SCREW
52PCS+1 spare
M3.5x30 mm SCREW
8PCS+1 spare
P5 P6
P7
M3.5x25 mm SCREW
16PCS+1 spare

03
Left
Front Right
Back

04
B
C
GH
PARTS
Front panel-down & middle
1PC
Back panel- upper & middle
1PC
Front panel- upper & middle
1PC Back panel-down & middle
D
Lower left panel -front & back
1PC
1PC
CARTON 1/4
J
1PC
Waterproof Cover
Layer
5PCS
OQ
Bottom of small house
2PCS
Hardware bag

K
PARTS
05
Side panel
2PCS
L
3PCS
Roof supporting bar
P
Bridge
2PCS
CARTON 2/4
Upper right panel- front & back
2PCS
E
I
Upper left panel-front & back
2PCS
V
Left roof
1PC

06
PARTS
CARTON 3/4
A
Lower right panel -front & back
2PCS
B
1PC
Lower left panel -front & back
F
1PC
Right roof
K
Side panel
2PCS
S
Right panel of small house
2PCS
R
Roof of small house
2PCS
T
2PCS
Left panel of small house
U
2PCS
Back panel of small house

07
PARTS
CARTON 4/4
K
Side panel
4PCS
Side supporting bar
6PCS
M
Laryer supporting bar with hook
fitting ( The hook fitting is on the
left side)
2PCS
N1
N
Layer supporting bar
10PCS
Laryer supporting bar with hook
fitting ( The hook fitting is on the
right side)
2PCS
N2

PRODUCT ASSEMBLY
01
Connect the front panels, screw Part A, B, D, E, H, I by 14XP3.
08
02
Attach side panel Part K to front side by 2XP4 screws in middle position and
2XP2 bolts in side position each side.
A
P3 X10
H
B
D
EI
P3 X4
H
D
A
I
E
B
K
P2 X2
X2
P4
K
X2
P4
P2 X2

PRODUCT ASSEMBLY
03
09
04
Attach side panel Part K to back side by 2XP4 screws in middle position and 2XP2
bolts in side position each side.
①Connect the back panels, screw Part A,B,C,E,G,I by 13XP3.
Bolt the layer supporting bar Part N by 4XP2.
P3 X10
A
BC
I
EG
P3 X3
P2 X4
Nx2
P4 X2
P4 X2
P2 X2
K
K
P2 X2
②

PRODUCT ASSEMBLY
05
Bolt 2 pieces of Part K together by 2XP1, then attach to front and back by 4XP1.
06
Bolt the other side 2 pieces of Part K together by 2XP1, then attach to front and
back by 4XP1.
10
P1 X4
P1 X4
Kx2
P1 X2
Kx2
P1 X2

PRODUCT ASSEMBLY
08
07
11
Bolt the layer support bars Part N ,N1& N2 by 12XP2.
(Position as shows in the picture)
Bolt the layer support bars Part N ,N1 & N2 to the other side by 12XP2.
(Position as shows in the picture)
P2 X12
Nx2
P2 X12
Nx2
Nx2
N1
Nx2
Nx2
Nx2
N2
N2
N1

PRODUCT ASSEMBLY
09

10
12
Attach layer Part O by 4XP5 screws. (Position as shows in the picture)
Attach layer Part O by 8XP5 screws. (Position as shows in the picture)
Attach layer Part Q by 4XP5 screws. (Position as shows in the picture)
P5 X4
O
P5 X8
Ox2
P5 X4
Q
①
②

PRODUCT ASSEMBLY
Attach layer Part O to the other side by 8XP5 screws. (Position as shows in the
picture)
Attach layer Part Q the other side by 4XP5 screws. (Position as shows in the
picture)
11
13
P5 X4
Q
P5 X8
Ox2
①
②

PRODUCT ASSEMBLY
12
①
②
Attach the 2 small houses, screw back panel Part U to side panel Part S&T by
4XP6, screw roof Part R by 4XP7.
Screw the small house to the layer from the bottom by 4XP7 each.
14
P7 X4
P7 X4
S
U
R
T
P6 X4
P7 X4

PRODUCT ASSEMBLY
13
14
Hook the bridge Part P to layers.
15
Bolt side supporting bar Part M by 6XP2.
P2 X6
Mx3

PRODUCT ASSEMBLY
16
Bolt side supporting bar Part M to the other side by 6XP2.
15
Attach roof Part F by 12XP5 screws.
P2 X6
Mx3
P5 X12
F
16
Velcro tape

PRODUCT ASSEMBLY
18
Open the door, walk into the cat run, and lock roof supporting bar Part L by 12XP4 screws.
17
17
Attach roof Part V to the other side by 12XP5 screws.
P5 X12
V
P4 X12
Lx3
Velcro tape

PRODUCT ASSEMBLY
19
Stick the Cover Part J by Velcro.
18
Finish
J

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal
injury,property damage or loss,whether direct,indirect,or incidental,resulting from
the incorrect attachment,improper use,inadequate miantenance,or neglect of this