aivituvin AIR 61 User manual

INSTRUCTION
MANUAL
AIR 61
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
02
M3.5x60mm SCREW
M6.0x30mm BOLT
8PCS+1spare 10PCS+1spare
P3 P4
M3.5x35mm SCREW
M3.5x40mm SCREW
16PCS+1spare 22PCS+1spare
P5 P6
M3.5x25mm SCREW
16PCS+1spare
P7 P8
Connect pieces
M3.0x16mm SCREW
24PCS+1spare
M4.0x30mm BOLT
2PCS 2PCS
(Only for 2 coops combination.
not available for one coop owner)

HARDWARE
P9
03
Spring latch
3PCS
P10
Lock
1PC
Coop Nesting box
Pen

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
BG
1PC 1PC
04
Front panel of coop
Back panel of coop
U W
2PCS
1PC
PVC Waterproof Strip
A
Y
1PC
Roof of pen Roof cap of pen
CARTON 1/2
Back panel of pen
1PC
Front panel of pen
HK
1PC
Ramp
1PC
Divider
1PC
R

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
1PC
05
Roof connect slat
Z
Hardware bag
( Only for 2 coops combination.
not available for one coop owner )
J
1PC
Splayed supporting bar

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
DE
FI
1PC
1PC 1PC
06
2PCS
Left panel of coop
Right panel of coop
Metal ramp support
L
M
1PC
1PC
Side panel of pen
C
Perch
Tray
N
1PC
1PC
Push handle Left panel of nesting box
CARTON 2/2
1PC
Right panel of nesting box
O

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
PQS
T
1PC
07
1PC
Roof of nesting box
Bottom of nesting box
Casters
2PCS
Roof of coop
1PC
Side panel of nesting box
VX
1PC
Roof cap of coop
2PCS

PRODUCT ASSEMBLY
01
02
08
Slide in metal tray Part E.
Insert perch Part F into slots inside the front and back panels.
①Attach the front Part A,the back Part B to the side panels Part C & D by
8xP3 screws.
②Notice to align with the dowels.
B
A
P
3
X
8
Fx2
C
D
①
②
E

PRODUCT ASSEMBLY
03
09
04
Ensure that all pen-panels have stapled-wire facing inside.
Attach Part G & H to coop by 4xP2 screws.
Attach metal ramp support Part I to the back panel by 2xP7 screws.
P2
X4
①
②
③
H
G
P7
X2
I
Attach the splayed supporting bar Part J by 2xP4 screws.
Screw ramp Part K to the bottom half of lower panel on Part D by
4xP6 screws. Notice not to block with the sliding door.
①
②
P6
X4
KJ
P4
X2

PRODUCT ASSEMBLY
05
10
M
Attach the push handle Part M to the side panel Part L by 4xP2 screws.
Attach the side panel Part L to front and back panel by 4xP3 screws.
①
②
P3
X4
L
P2
X4

PRODUCT ASSEMBLY
06
11
Attach the side panel of nesting box Part N&O to the coop by 1xP2 &
1xP4 screws each side.
(Notice screw the P4 from inside in the upper position, screw the P2
from outside in the down position)
N
O
P2 X2
P4 X2

PRODUCT ASSEMBLY
07
12
Bolt the caster Part Q to the side panel of nesting box Part P by
4xP1 screws each.
Attach the side panel of nesting box Part P to the sides by 4xP3
screws.
Qx2
P3 X4
P1 X8
①
②
P

PRODUCT ASSEMBLY
08
13
09
Drop in bottom of nesting box Part S.
Slide in divider Part R.
S
Make sure the lock is functioning properly before locking the roof.
Attach the roof of nesting box Part T by 6XP6 screws.
T
P6
X6
R
①
②
①
②

PRODUCT ASSEMBLY
10
14
11
Attached PVC Waterproof Strip Part Uto the nesting box by 2XP4
screws.
P4
X2
U
Wx2
P4
X16
Attach roof panels Part V to the coop by 8xP4 screws.
Attach roof panels Part W to the pen by 8xP4 screws.
①
②Vx2

PRODUCT ASSEMBLY
12
15
13
Ensure top roof panels line up with each other before screwing roof caps
Part X&Y by 10XP5 screws.
Finish here for only buying one coop
P5
X4
X
P10
X1
Attach the spring latch P9 to the doors by 2xP6 screws each.
(Notice the direction of latch)
Attach lock P10 to the side door by 4XP6 screws.
①
②
P5
X6
Y
P6
X6
P9
X3
P6
X4

16
Notice
Read Before Assemble!
Pls ignore the following for only one coop owner !
The side pen panel Part L, the push handle Part M ,the pen lock P10 are
not needed in 2nd coop.
①
②

17
Notice
Read Before Assemble!
The following pages are assemble steps for 2nd coop.
The casters, the side pen panel Part L, the push handle Part M, the pen lock
P10 are not needed in 2nd coop.
The assemble direction of the hutch Part C &D, are different pls notice.
①
②
③

14
18
DA
C
B
P
3
X8
PRODUCT ASSEMBLY
Attach the front Part A,the back Part B to the side panels Part
D & C by 8xP3 screws.
Repeat the same assembly ways from step 2-step12 the same
as the 1st coop.
(Very important !)
！
Notice the direction of
Part C & D is different
with the 1st coop.
①
②