aivituvin AIR 66 User manual

I
AIR 66
www.aivituvin.com
NSTRUCTION
MANUAL

Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure
every 90 days.
Fasten screws loosely during initial assembly. Do not
fully tighten screws until the item is completely
assembled.
Do not use or store this item in the proximity of open
flame or flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop
using this product until repairs are made and/or factory
replacement parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’s instructions as this could void the
product warranty.
Please retain these instructions for future
NOTICE
01

02
PHILLIPS
SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY
M6.0x50 mm BOLT
8PCS+1 spare
M3.5x60 mm SCREW
14PCS+1 spare
M3.5x40 mm SCREW
8PCS+1 spare
M3.5x35 mm SCREW
14PCS+1 spare
TOOLS REQUIRED
HARDWARE
P1 P2
P3 P4
P5 P6
M3.5x30 mm SCREW
16PCS+1 spare
M3.5x25 mm SCREW
22PCS+1 spare
P5 P6
P5 P6
P7 P8
M3.0x14 mm SCREW
30PCS+1 spare 1PC
Lock

03
HARDWARE
P5
4PCS
P9
Spring latch
Waterproof PVC
1PC
P10

04
A B
PARTS
Folding of Wire Pen
1PC 1PC
Support Shelf of Bottom Ramp
2PCS
D
Ramp
CARTON 1/2
E
F
Folding of Wooden Coop
1PC
Connect Bar
2PCS
H
Tray
1PC
I
3PCS
Perch
N
Divider
2PCS
Q
PVC waterproof strip
2PCS

05
PARTS
CARTON 2/2
Support
1PC
C
G
1PC
Support Panel of Middle Ramp
Support of Tray
1PC
S
Hardware bag
K
2PCS
Panel of Nesting Box
J
2PCS
Panel of Nesting Box
L
2PCS
Side Panel of Nesting Box
O
P
2PCS
Roof of Nesting Box
2PCS 2PCS
M
Bottom Floor of Nesting Box
Roof of Coop
R
2PCS
Cap

PRODUCT ASSEMBLY
01
Expand the part of wire pen Part A .
①Attach the Part C to the Part B by 2XP5 screws.
②
③Attach the Part B to the left side of wire pen by 6XP6 screws.
06
A
B
C
P5 X2
Front
P6 X6

PRODUCT ASSEMBLY
02
07
03
①Expand the part of wooden coop Part E.
②Attach the connect bar Part F to the left & right side of coop by 12XP5 screws.
(Please line up the same level of bottom edge)
①
②
E
D
P7 X4
Fx2
P5 X12
Front
S
P5 X2
Attach the ramp Part D to the Part B by 4XP7 screws.(Notice the direction of ramp)
Attach the support bar Part S to the corner of front and left side panel by 2X P5 screws.
Front

PRODUCT ASSEMBLY
04
08
05
①Slide in tray Part H in front.
②Slide in support panel of middle ramp Part G in back.
Connect the wooden coop and wire pen with connecting bar by 2XP2 screws each side.
G
P2 X2
H
P2 X2
Front

PRODUCT ASSEMBLY
06
07
①Attach the ramp Part D to the support panel of middle ramp Part G by 4XP7 screws.
(Notice the direction of ramp)
②
09
Insert 3PCS perches Part I into the slots inside left and right side panel of coop by 6XP4
screws.
P4 X3
D
P4 X3
Ix3
P7 X4
P2 X2
Attach the Part G to side panel by 1 X P2 each sides.

PRODUCT ASSEMBLY
08
09
Attach the nesting box,attach the Part K & Part J to the coop by 4XP1 bolts each sides.
(Notice the direction of Part K & Part J )
10
Attach the side panel Part L to the Part K & Part J by 4XP3 screws each sides.
P3 X4
P1 X4
JJ
K
K
P1 X4
P3 X4
L
L

PRODUCT ASSEMBLY
10
11
①Drop in the bottom floor Part M to the nesting box each sides.
②Insert the divider Part N into the slots of bottom floor each sides.
11
M
Attach the nesting box roof Part O to coop by 4XP7 screws each sides.
P7 X4
O
M
N
N
P7 X4
O

PRODUCT ASSEMBLY
13
12
Attach the coop roof Part P by 8XP4 screws.
12
P4 X8
Px2
P6 X4
Q
P6 X4
Q
①Attached PVC Waterproof Strip Part Q to the nesting box by 4XP6 screws each sides.
②Ensure top roof panels line up with each other before screwing the cap 2XPart R by 8XP6
screws
Rx2
P6 X8
P10
③Put the Waterproof pvc P10 in the connection position of 2 roof cap to avoid the
water leakage.

PRODUCT ASSEMBLY
14
①Attach the latch P8 to the front tray by 6xP7 screws
②Attach the spring latch P9 to the two front doors by 2xP7 screws each latches.
(Notice the direction of latch)

15
13
Attach the spring latch P9 to the two back doors by 2xP7 screws each latches.
(Notice the direction of latch)
P7
X6
P8
X1
P9
X1
P
7
X2
P9
X1
P
7
X2
P9
X1
P
7
X2
P9
X1
P
7
X2

14
Notice
Read Before Assemble!
The below steps are for chicken coop & run combination by 4xP2
screws each sides. If you do only buy one chicken coop ,pls ignore
the following.
Finish
Combination 1 Combination 2
Combination 3

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal
injury,property damage or loss,whether direct,indirect,or incidental,resulting from
the incorrect attachment,improper use,inadequate miantenance,or neglect of this