aivituvin XZ7001 User manual

INSTRUCTION
MANUAL
XZ7001 XZ7003
WARNING
Maunfacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.
www.aivituvin.com

Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’ s instructions as this could void the product
warranty.
Please retain these instructions for future reference.
NOTICE
01

0302
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
M3.5x50mm SCREW
4PCS+1 spare
M3.5x40mm SCREW
18PCS+1 spare
M3.5x25mm SCREW
16PCS+1 spare
M3.0x16mm SCREW
10PCS+1 spare
1PC 1PC
A B C
D E F
G H I
TOOLS REQUIRED PARTS
HARDWARE
P1 P2
P3 P4
P5 P6
Front panel of pen
1PC
Back panel of pen
1PC
Left side panel of pen
1PC
Divider panel
1PC
Upper tray
1 PC
Lower tray
1PC
Front panel of hutch
1PC
Back panel of hutch
1PC
Right panel of hutch
1PC

J K L
M N
PARTS PRODUCT ASSEMBLY
01
02
Attach Part A, Part B and Part C by 6pcs of P2 screws.
Attach Part G to Part A and Part B by 4pcs of P2 screws.
P2 X4
G
0504
A
B
C
P2 X6
Casters without brake
2 PCS 2 PCS
Brake Casters
Pen roof
1PC
Huntch roof
1PC
Ramp
1PC

PRODUCT ASSEMBLYPRODUCT ASSEMBLY
05 Repeat on the other side.
06 Slide in two trays.
04 Attach the pen to hutch by 2pcs of P1 screws.
03 Attach the pen Part D,Part E,Part F by 4 pcs of P2 screws.
P2 X4
P1 X2
E
D
I
FP1 X2
0706
H

PRODUCT ASSEMBLYPRODUCT ASSEMBLY
09 Screw two brake casters Part N to the back of hutch legs by P3x8.
10 Put ramp Part L on the divider panel.
08
07 Put in rabbit chewing toy.
0908
P5 X1
P3 X8
L
Screw two casters without brake Part M to the front of hutch legs by P3x8.
Mx2
P3 X8
Nx2

PRODUCT ASSEMBLY
PRODUCT ASSEMBLY
12 ① Attach the pen roof Part J by 4pcs of P2 screws.
② Screw the roof hinge P6,one side to the roof by P4x2,the other side to the right
panel by P4x2.
11Screw the roof hinge to the back by 3pcs of P4 screws on each side.
P6 X1
P4 X2
1110
LOCKED
OPEN
J
P2 X4
P4 X6
P4 X2

THANK YOU
Thanks for your support to Aivituvin.
Your satisfaction is our #1 priority.
Once the items are received, opened, and deemed to be faulty
or other problems.
Pls contact us at ser[email protected] for the solution.
We will feedback to you within 24 hours.
If you are happy with the shopping ,welcome to share photos
and thoughts with others .
HELP CENTER
ser[email protected]
Question about your product? we're here to help contact us via
Returns & Refunds
?
Product AssemblyOrders FAQProduct inquiry
12
www.aivituvin.com