aivituvin AIR 28 User manual

I
AIR 28
www.aivituvin.com
NSTRUCTION
MANUAL

Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure
every 90 days.
Fasten screws loosely during initial assembly. Do not
fully tighten screws until the item is completely
assembled.
Do not use or store this item in the proximity of open
flame or flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop
using this product until repairs are made and/or factory
replacement parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’s instructions as this could void the
product warranty.
Please retain these instructions for future
NOTICE
01

02
PHILLIPS
SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY
4PCS+1 spare
M3.5x40 mm SCREW
16PCS+1 spare
M3.0x16 mm SCREW
21PCS+1 spare
Latch
1PC
TOOLS REQUIRED
HARDWARE
P1 P2
P3 P4
P5 P6
Roof hinge
2PCS
SPRING LATCH
2PCS
P5 P6
M3.5x60 mm SCREW
M3.0x16 mm SCREW
4PCS+1 spare
P7

03
HARDWARE
Hutch
Pen

04
G
PARTS
Front and back panel
2PCS
Side panel of pen Roof of hutch
1PC
I
A
B
Front panel
1PC 1PC
Back panel
C
1PC
Side panel
D
E
Middle panel
1PC 1PC
Divider
F
2PCS
Floor
1PC
H

05
PARTS
J
Roof of pen
1PC

PRODUCT ASSEMBLY
01
Attach the front Part A and the back Part B to the side Part C by 4xP2.
06
A
B
P2 X4
02
Attach the middle panel Part D to the front and back by 4xP2.
D
P2 X4
C

PRODUCT ASSEMBLY
Put the floor Part F into the hutch.
03
07
Fx2
04
E
Insert the divider Part E to the hutch.

PRODUCT ASSEMBLY
05
Attach the roof Part I to the hutch by 9xP3.
06
Attach the roof hinge P6 with 8xP3.
08
I
P6 X2
P3 X9
P3 X8

PRODUCT ASSEMBLY
08
07
Attachthepanel Part G to the front by 2xP1.
09
P1 X2
P1 X2
G
Repeat the Part G assembly in the opposite side by 2xP1.
G

PRODUCT ASSEMBLY
09
Attach the side pen panel Part H to the sides by 2xP2 each side.

10
10
P2 X2
Attach the roof Part J to the pen by 4xP2.
J
H
P2 X2
P2 X4

PRODUCT ASSEMBLY
11
Attach the spring latch P5 to the front door by 2xP3. 
12
11
P3 X2
Attach the spring latch P5 to the back door by 2xP3.
P5 X1
P3 X2
P5 X1

PRODUCT ASSEMBLY
13
Attach the lock P4 to the side by 4xP7.
12
P7 X4
P4 X1
12

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal
injury,property damage or loss,whether direct,indirect,or incidental,resulting from
the incorrect attachment,improper use,inadequate miantenance,or neglect of this