aivituvin AIR 43 User manual

INSTRUCTION
MANUAL
AIR 43
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
30MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
02
M3.5x35mm SCREW
M3.5x25mm SCREW
M4.0x60mm SCREW
11PCS+1spare
12PCS+1spare 3PCS+1spare
P5 P6
Hinge
2PCS
Plastic Feet
4PCS
M3.0x16mm SCREW
20PCS+1spare

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
D E F
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC
1PC
Front panel
PVC curtain Back panel
Left side panel
1PC Divider panel
Left side bottom floor
Right side panel
Right side bottom floor
Roof

PRODUCT ASSEMBLY
01
02
04
Screw Part I to the INSIDE of Part A by 2xP2 screw.
Screw the curtain Part B to the INSIDE of Part A by 3xP3 screws.
P3X
A
3
P2X
2
A
B
I

PRODUCT ASSEMBLY
03
04
05
Pls line up the Part D & Part E as shown on the picture before
attach the Part C to Part E & D by 6xP1.
Put in bottom floor Part F and G.
P1
X6
C
D
F
.
line up the same level
Side Panel
(Part D & Part E)
Back Panel (Part C)
E
G

PRODUCT ASSEMBLY
05
06
①Pls line up the Part D & Part E as shown on the picture before
attach the Part A to Part E & D by 6xP1.
②
CE
Screw the divider panel to the bottom panel by 1xP2 screw.
line up the same level
Side Panel
(Part D & Part E)
Front Panel (Part A)
DA
P1
X6
P2
X1

PRODUCT ASSEMBLY
06
07
07
①Screw the roof hinge to the back by 4xP2 screws on each one.
②Notice to level up before screwing together.
①Screw the roof hinge P5, one side to the roof by 2xP4 screws,
the other side to the left side panel by 2xP4 screws.
②Repeat on the other side.
P4
X12
H
P5
X2
P4
X8

PRODUCT ASSEMBLY
08
08
Attach 4pcs of P6 plastic feet.
P6
X4
P3
X8

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.