aivituvin AIR42 User manual

INSTRUCTION
MANUAL
AIR42
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’ s instructions as this could void the product
warranty.
01

PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
6PCS+ +1 spare
P1 P2
P3
02
M3.5x60mm SCREW
16PCS++1spare
M4.0x45mm SCREW
4PCS+1pare
M6.0x50mm Bolt
P4
8PCS ++1spare
M3.5x35mm SCREW
P6
TOOLS REQUIRED
HARDWERE
P5
20PCS++1spare
M3.5x25mm SCREW
16PCS++1spare
M3.5x20mm SCREW

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
2 PCS
1 PC
03
HI
2PCS 1 PC
1 PC
1 PC
1 PC
Back panel-Down
1 PC Right & Left panel-Upper
Front panel-Upper Front panel-Down Back panel-Upper
Left panel-Down
Right panel-Down Bottom wire netting Tray
1 PC
PARTS

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
2 PCS
Front panel of small
house
04
1 PC
Ramp
1 PC Standing bar
PARTS
M N O
Bottom panel of small
house
1 PC
Back panel of small
house
1 PC
Right & Left panel of
small house
P Q R
2 PCS
Roof cap
1 PC
Top panel of small
house
1 PC
Roof
2PCS

05
ST U
2 PCS
Wooden feeder
1 PC
Casters with brakes
2 PCS Casters without
PARTS

PRODUCT ASSEMBLY
01
02
06
Attach the small house!Attach the part P,L ,2x N by 6X P6 screws.
Attach the back panel of small house part M by 6XP6 screws.

L
N
P
P6 X6
P6 X6
M
N

PRODUCT ASSEMBLY
03
04
0 7
Attach the hutch!Attach the Back panel-Down part D,to the side parts
F & G by 4X P3 screws.
Attach the Bottom panel of small house part O by 4XP6 screws.
O
P6 X4
P3 X4
F
G
D

PRODUCT ASSEMBLY
05
06
0 8
Attach the Wooden feeder part Uby 2XP1 screws.
AttachtheFrontpanel-DownpartBby4XP3screws.
P1 X2
U
P3 X4
B

PRODUCT ASSEMBLY
09
08
Put the bottom wire netting 2pcs of part H inside the cage as show
on the picture. 
07
Slide in the tray part I.
I
H
H

PRODUCT ASSEMBLY
09
10
Put the ramp part J into the cage as show on the picture.
Put the one of standing bar par K into the wire(in any place you
want)
10
J
K

PRODUCT ASSEMBLY
11
12
Attach the Back panel-Upper part C by 2X P2 screws.
Attach the small house to the upper left corner of back panel Part C
by 2X P1 screws.
11
C
P2 X2
P1 X2

PRODUCT ASSEMBLY
13
Attach the Right & Left panel-Upper part E to back panel by 4 X P3
screws.Down to the side panels by 2 X P2 screws.
12
14
①Attach the Front panel-Upper part A to side panels by 4 X P3
screws,Down to the Front panel-Down by 2 X P2 screw.
②Put the other standing bar par K into the wire(in any place you want).
P3 X4
P2 X2
E
K
A
P2 X2
P3 X2
P3 X2

PRODUCT ASSEMBLY
15
1 6
13
Attach the roof cap Part R by 4X P5 screws.
Attact the roof Part Q to the hutch by 8 X P4 screws
P4 X8
Q
Q
R
P5 X4

PRODUCT ASSEMBLY
17
18
14
Screw 2pcs of Casters without brakes part T to the front 2 legs
by 8 X P5 screws.
Screw 2pcs of Casters with brakes part S to the back 2 legs by
8 X P5 screws.
SX2
P5 X8
TX2
P5 X8
P5
Finish

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.