aivituvin AIR 23 User manual

INSTRUCTION
MANUAL
AIR 23
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
02
M3.5x40mm SCREW
M6.0x50mm BOLT
4PCS+1spare 24PCS+1spare
P3 P4
M3.5x35mm SCREW
M3.5x50mm SCREW
8PCS+1spare 12PCS+1spare
P5 P6
M3.0x16mm SCREW
M3.5x25mm SCREW
4PCS+1spare 8PCS+1spare
P7
Spring latch
2PCS

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
D E
1PC
1PC 1PC
03
1PC
1PC
Front panel of coop -
Upper
Back panel of coop -
Upper Left panel of coop
Right panel of coop
Left panel of nest box
F
1PC
Right panel of nest box
G H
1PC
1PC
Bottom panel of nest box
Front panel of nest box
I1
1PC
Front panel of pen - Down

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
I2 J K
L M1
1PC
1PC 1PC
04
1PC
1PC
Back panel of pen - Down
Plastic tray Side panel of pen - Down
Perch
Front panel of side pen
M2
1PC
Back panel of side pen
N O
2PCS
1PC
Side panel of side pen
Roof of coop
P
1PC
Roof of nest box

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
Q R S
1PC 1PC
05
1PC
Roof of side pen
Ramp Roof cap

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
06

PRODUCT ASSEMBLY
01
02
07
①Align dowels on “A” and “B” with hole on “C” and “D”by screw 6xP2.
Attach the Coop to the Pen using 6xP2.
②
①Ensure screw holes on long side of
②Ensure that all pen
③All dowels on
④Ensure all corner line up before screwing together .
“K”with hole on “I1”and “I2”by screw 4xP2.
-panels have stapled-wire facing inside.
“I1”and “I2”are oriented at top.
P
2
X
B
4
K
I2
I1
Screw Holes
This area is part of the
Pen
The area is called
the Coop
D
A
C
P
2
X
6
P
2
X
6

PRODUCT ASSEMBLY
03
08
①Insert “L” piece into slots inside “C” and “D”.
②Slide “J” into bottom slot of Coop.
P1
X4
L
J
04
Bolt “E’’ and “F” to Coop by 4xP1.①Screw “H” to “E’’ and “F” by 4xP4.
②
E
P4
X4
HF

PRODUCT ASSEMBLY
05
06
09
①Drop in Nest Box floor “G”.
②Screw ladder R into bottom half of lower panel on D by 4xP6,
so as not to interfere with sliding door.
Screw roof panels “O” to the Coop by 8XP4.
P6
X4
G
R
Ox2
P4
X8

PRODUCT ASSEMBLY
07
08
10
①
②
Ensure top roof panels line up with each other before screwing
“S” by 4xP5.
Ensuring the latch with lock on “H” before attach nest box lid at
the hinges.
P5
X4
S
Connect the Pen to the Coop by 4XP3 on each side.
P3
X4
M2
M1
P3
X4

PRODUCT ASSEMBLY
09
10
11
Align dowels on “N” with holes on “M1” and “M2” by 4xP2.
Complete the side pen by screwing the top roof Part Q to the front
& back Part M1, M2 ,side Part N by 4xP2.
P2
X4
N
This area is a part
of the Pen
P2
X4
Q

PRODUCT ASSEMBLY
11
12
Screw the spring latch by 4xP6, please pay attention to the direction.
P7
X1
Finish
P6
X2
P7
X1
P6
X2

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.