ATCOM Rainbow1 User manual

Rainbow1 Quick Start Guide
Version 1.0
2014-03-21

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
Content
1. Installation and access ........................................................3
1.1 Connection ......................................................................3
1.2 Installation instruction.......................................................3
1.3 Check IP .........................................................................9
1.4 Login to web ....................................................................9
2. Configure phone to register SIP account.................................9
2.1 Network Configuration.......................................................9
2.2 Account Configuration .....................................................10

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
1. Installation and access
1.1 Connection
Set up Rainbow1 as below:
1.2 Installation instruction
1. Desktop installation
A. Put the bottom side of the IP phone upside and press the plate
into the slot, please refer the picture as below:

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
B. Press the other plate into the slot according to the direction of
the arrow
C. It is the right picture after fixing the feet below:

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
D. Disassemble the feet:
Push the plate and pull the feet according to the direction of the
arrow. When the plate is pulled out of the slot, you can take off the
feet
2. Wall-hung Installation
A. Put the bottom side of the IP phone upside and press one-side
joints of wall-hung stand bracket into the slot, please refer the
picture as below:

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
B. Press the other side joints into the slot according to the direction
of the arrow

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
C. After install the wall-hung stand bracket, press one-side joints of
stand bracket into the slot, please refer the picture as below:

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
D. Press the other side joints into the slot according to the direction
of the arrow
E. Knock in nails or screws on the wall according to the proportion
of the distance between the hanging holes as below:
F. It is the right picture after fixing the stand bracket below:

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
G. Disassemble the stand bracket:
Push the spring joint of stand and pull the stand according to the
direction of the arrow.

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
1.3 Check IP
Rainbow1 use DHCP mode by default, and you can review its
current IP address by pressing key when it is powered on and
connected to the network.
1.4 Login to web
Modify your computer’s IP address to the same network as
Rainbow1. Enter Rainbow1’s IP address in the web browser and
press Enter, then you will access to Rainbow1's user webpage
without password.
Click ‘admin’ which is on the right corner to enter administrator
webpage.
2. Configure phone to register SIP account
2.1 Network Configuration
LAN Port Configuration
Enter "Network" -> "Basic" page.
There are 3 ways to connect to internet DHCP, Static and PPPoE,
please choose one according to your own situation.

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
Network mode: you can choose DHCP, Static and PPPoE
DHCP: Rainbow1 default to use DHCP to obtain IP from DHCP
Server.
Static: If you want to set the IP as static, you should fill IP,
Netmask, Gateway and DNS information.
PPPoE: If Rainbow1 is connected to the modem, you should fill
ADSL account and password which are assigned by your network
service provider.
Password Configuration
Enter "Network" -> "Advance" page.
There are 2 modes to set the authority of web accessing and
command line: User mode and Admin mode. All the parameters can
be visible and changed in Admin mode while part of them can be
visible in User mode.
Enable Web Server: enable or disable web access. If choose
"no", you can not access Rainbow1’s webpage.
Admin password: set admin webpage access
password.(username:admin)
User password: set user webpage access
password.(username:user)
2.2 Account Configuration
Enter "Account" -> "SIP" page to configure SIP account which is
provided from the SIP Server.

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED
Display Name: This name will display on the screen of
Rainbow1. It will display the name configured for the SIP
account by the SIP server preferentially. It can also be kept
blank.
User ID: Username of SIP account.
Authenticate ID: normally is the same with User ID, can also be
kept blank if there is no special requirement from the SIP
server.
Password: Password of SIP account.
Sip Server: SIP server address, support both IP address and
domain name.
Sip Port: SIP server port, default is 5060.
After configured and clicked ‘Submit’ to enable register this account,
please check the status of this account in System Status page.
The Registration State will be registered if this account registered
successfully.

Rainbow1 Quick Start Guide
ATCOM TECHNOLOGY CO., LIMITED