Bradley S19-110HFP User manual

Installation
S19-110HFP
Frost-Proof Drench Shower
(18", 3', 4', 5' or 6' Bury Depth)
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly of Components . . . . . . . . . . . . . . . . . . . . . 4–5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Bradley S19-110HFP18 Free Standing Safety Drench Shower
Bradley S19-110HFP3 Free Standing Safety Drench Shower
Bradley S19-110HFP4 Free Standing Safety Drench Shower
Bradley S19-110HFP5 Free Standing Safety Drench Shower
Bradley S19-110HFP6 Free Standing Safety Drench Shower
netzerotools.com
netzerotools.com
netzerotools.com

2
S19-110HFP Installation
5/25/2012
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to the
eyewash should be “ON” at all times. Provisions shall be made to prevent unauthorized
shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per ANSI
Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to ensure
compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment per
ANSI Z358.1.
Installation
THIS
SIDE
UP
Packing List

P.O.Box309, Menomonee Falls, WI 53051
R
TESTTHISUNIT EACHWEEK
Test-operatevalve(s) each week and sign below.
Reportanymalfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelquechose qui ne va pas fait
unrapport immédiatement.
P.O.BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
114-051
Supplies Required:
3⁄8" floor anchors and bolts

netzerotools.com
netzerotools.com

3
Installation S19-110HFP
Bradley฀•฀215-165HFP Rev. J; ECN 12-05-016A 5/25/2012
Installation
Step 1: Concrete footing and base
IMPORTANT: Make sure the solid
nipple is located where shown on
page 4.
IMPORTANT: Make sure the pipe tee is
aligned toward the excavation.
Step 2: Valve assembly
3. Backfill as specified.
Step 3: Assemble components
IMPORTANT: Do not rely on Bradley’s
Drench Shower to support supply
piping.
by installer).
NOTE: All dimensions assume standard thread engagement.
Variations in manufacturing allow for +/- 1⁄8" (3mm) per
threaded joint. To find the tolerance of a dimension,
add the number of thread joints in between a
dimension and multiply it by 1⁄8" (3mm).
84"
(2134mm)
to Floor
233⁄16"
(589mm)
4½"
(114mm)
73⁄16"
(183mm)
37½"
(953mm)
Ø9" (229mm)
Flange with (3)
Ø3⁄8" (10mm)
Holes on Ø8"
(203mm) Bolt
Circle
Ø3.1"
(78.7mm)
Concrete footing (not
less than 3 cubic yards of
crushed stone around and
below drain down waste
outlet for drainage
NOTE: 1⁄8" tube
drain down waste
to spill on grade,
french drain or
other safe waste
1¼" NPT
Supply Inlet
18" (457mm)
3' (914mm)
4' (1219mm)
5' (1524mm)
6' (1829mm)
bury depth
netzerotools.com
netzerotools.com

4
S19-110HFP Installation
5/25/2012
Assembly of Components
P.O. Box 309, Menomonee Falls,WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1STWÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signe en bas.S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
15
16
1
14
34
5
7
9
10
11
12
8
6
2
13
114-090
bradleycorp.com
NOTE: Use
teflon tape
only.
netzerotools.com
netzerotools.com

5
Installation S19-110HFP
5/25/2012
Assembly of Components
5.19 5.21
netzerotools.com
netzerotools.com

6
S19-110HFP Installation
5/25/2012
Parts List
Item Part No. Qty. Description
1 131-042 1 Base
2 S06-136 1 3 169-727 1 4 113-006NA 2 5 S90-252 1 S90-089 1 S90-090 1 S90-091 1 S90-253 1 5.1 S08-040 1 Handle Assembly
5.2 142-002BB 1 Stainless Steel Washer
5.3 110-108 1 5.4 124-001BS 1 Gasket
5.5 135-001AP 1 5.6 132-012 1 5.7 113-772 1 113-773 1 113-774 1 113-775 1 113-776 1 5.8 120-022K 1 120-022D 1 120-022E 1 120-022F 1 120-022G 1 5.9 169-727A 1 Item Part No. Qty. Description
5.10 145-072 1 5.11 132-011 1 Retainer
5.12 118-246 1 5.13 160-138 1 5.14 169-920 1 5.15 182-061 1 Spacer
5.16 142-002CC 3 Washer
5.17 160-251 1 5.18 125-001CD 1 5.19 110-109 1 5.20 165-038 2 Roll Pin
5.21 161-061 1 5.22 169-890 1 Connector
6 169-852 1 7 113-006MG 1 1⁄8"
8169-846 1 9 151-001 2 10 111 169-847 2 12 S24-188 1 13 169-853 1 14 113-1181 1 15 114-090 1 16 204-421 1 17 269-915 1 
netzerotools.com
netzerotools.com