Lionelo Liam User manual

1
1. Important information
Before using the car safety seat please read this user manual carefully.
Improper use may lead to a serious threat to the life of your child.
NOTE:
Do not mount the safety seat on a passenger seat equipped with an airbag.
2. Function
LIAM has been classified as a "universal" car safety seat for children from Group 0+ and I, that is for those
weighing less than 18 kg.
- Group 0+: children weighing less than 13 kg
- Group I: children weighing less than 18 kg
•Do not install the safety seat in a forward-facing position if the child weighs less than 9 kg.
•Children from group 0+ and I must use the 5-point safety harness (included with the seat), while the
safety seat itself must be secured by the vehicle’s 3-point seat belt. The seat can be installed in
vehicles approved by the UN/ECE (Regulation No 16) or other relevant regulations.
Correct installation of the safety seat
Incorrect installation of the safety seat
Do not mount the safety seat on a passenger seat equipped with an airbag
The installation of the safety seat is possible if a vehicle’s middle seat is equipped with
a 5-point safety belt
3. Safety notes
•Do not ever leave your child unattended in the safety seat.

2
•Any modifications to the safety seat without the consent of the competent authorities are
not allowed. Failure to follow the manufacturer's installation instruction may result in danger
to the child.
•It is recommended not to expose the safety seat to direct sunlight. Otherwise it may
become hot and cause harm to the child’s skin.
•Do not place any heavy objects on the vehicle’s rear windscreen shelf. Such an object may
affect the safety of the child during an accident or heavy breaking.
•Do not use the safety seat without the original cover. Do not replace the cover with the one
that is not recommended by the manufacturer. It is an integral part of the product and it
contributes to the safety of the child.
•The seat can be installed in vehicles approved by the UN/ECE (Regulation No 16) or other
relevant regulations.
•The rigid items and plastic parts of the safety seat shall not be responsible for the daily
exploitation of the vehicle.
•During stopovers, ensure that the child does not come out of the safety seat unsupervised.
Always lock the vehicle’s doors.
•Do not use the safety seat if any of its parts is damaged.
•When fastening the safety belts or harness always follow the instructions specified by the
manufacturer.
•Luggage or other items should be secured so as not to cause damage to the child.
•The safety seat should be replaced if it has been subjected to violent forces during an
accident.
•Do not install the safety seat in a way other than the one described in the manual.
4. Accessories
back
headrest
shoulder strap pad
safety harness
pad
safety lock
buckle pad
seat
adjustable base
harness adjustment strap

3
5. Usage
5.1 Harness adjustment, straps tightening / loosing
5.1.1 Normally the straps are always secured, as shown in the picture 5.01. In this position, you
can tighten the straps to adjust their length to the height of the child.
(Picture 5.02)
Picture 5.01
Picture 5.02
harness
adjustment strap
adjustable base
belt guides
springs
belts connector

4
5.1.2 In order to loosen the shoulder straps, use one hand to press the button (Picture 5.03 and 5.04) and
the second one to pull the shoulder straps.
Picture 5.03
Picture 5.04
5.2 Shoulder straps connection
5.2.1 Hook the shoulder straps in the harness connector as shown in the Picture 5.05.
5.2.2 Run the harness strap through the harness connector (Picture 5.06).
Picture 5.05 Picture 5.06
Press the
adjustment
button
Pull the shoulder
straps down

5
5.3 Adjustment strap connection
5.3.1 Attach the strap to the hook (Picture 5.07).
5.3.2 Thread the hook through the hole at the front of the seat (Picture 5.08). Then pull the
shoulder straps up so as to lock the harness at the underside of the seat.
5.3.3 To remove the adjustment strap follow the above steps (up to point 5.3.2) in reverse order
(Picture 5.09).
Picture 5.07
Picture 5.08
Picture 5.09
5.4 Safety lock
5.4.1 In order to fasten the buckles in the safety lock, first joint them (Picture 5.11) and insert the
combined buckle into the safety lock (from the top) (Picture 5.11). The “click” sound indicates
that the safety lock has been properly fastened.
5.4.2 To remove the buckles from the safety lock, press the red button on it (Picture 5.12).
Prise off
Seat hole
.
Seat hole
.

6
Picture 5.10, 5.11 Picture 5.12
5.5 Shoulder strap height adjustment
5.5.1 Loosen the shoulder straps.
5.5.2 Remove the shoulder straps from the harness connector.
5.5.3 Remove the shoulder straps from the slots.
5.5.4 Choose the most appropriate slots and run the shoulder straps through them. The slots
position should be determined by the height of the child.
5.5.5 Hook the shoulder straps in the harness connector.
5.5.6 Tighten the shoulder straps.
5.6 Proper height of the shoulder straps
5.6.1 The shoulder straps should be neither too tight nor too loose (Picture 5.13).
5.7 Seat angle adjustment
The seat can be adjusted to three different positions.
5.7.1 In order to change the seat angle, put your hand under the seat, then press and hold the
lock. Moving the hand up or down choose a desirable seat angle. In order to tilt the seat
down you can use the other hand to push the upper edge of the seat (Picture 5.14).
Too low (tight)
Correct
Too high (loose)

7
5.7.2 The arrows on both sides of the base indicate the seat angle (Picture 5.15).
5.7.3 Red arrows indicate position 1 and 2. These settings are reserved for the I age group and
can only be used when the seat is installed in a forward-facing position (Picture 5.16).
5.7.4 Position 3 indicated by blue arrow is reserved for children from the 0+ age group. It is a
reclining position, which requires the seat to be installed in a rear-facing way (Picture 5.17).
5.7.5 When the seat position is not aligned with any of the arrow, it means that it has been adjusted
improperly and can be dangerous for the baby. In that case it is necessary to correct the seat
position immediately.
Picture 5.14 Picture 5.15
Picture 5.16 Picture 5.17
6. Installation for the group 0+
The safety seat must be installed in a rear-facing position. The back must be tilted to the position number 3

8
indicated by the blue arrow.
6.1. Installation of the safety seat in a car
6.1.1. Adjust the back of the safety seat so that it is in the position number 3 indicated by the blue
arrow.
6.1.2. The safety seat should be installed in a car equipped with 3-point seat belts.
6.1.3. First, pull the vehicle’s seat belts as much as possible.
6.1.4. Run the lap belt and the shoulder belt through the safety seat (Picture 6.01).
6.1.5. Ensure that the vehicle’s seat belt connector is properly locked in a buckle.
6.1.6. Ensure that the vehicle’s seat belts are not twisted.
Picture 6.01
6.2. Secure the child in the safety seat with the 5-point safety harness.
7. Installation for the group I
The safety seat must be installed in a forward-facing position. The back must be locked in the position
number 1 or 2 indicated by the red arrows.
7.1. Installation of the safety seat in a car
7.1.1. Adjust the back of the safety seat so that it is in the position number 1 or 2.
7.1.2. Install the safety seat in a forward-facing position, in a car equipped with 3-point seat belts.
7.1.3. First, pull the vehicle’s seat belts as much as possible.
7.1.4. Run the lap belt and the shoulder belt through the safety seat (Picture 7.01, 7.02). Thread
the lap belt through the “C” hole and pull it out of the “D” hole at the other side.
At the same time carry the shoulder belt through the special hole behind the back of the
safety seat.

9
7.1.5. Ensure that the vehicle’s seat belt connector is properly locked in a buckle.
7.1.6. Ensure that the vehicle’s seat belts are not twisted.
7.2. Securing a child with the 5-point safety harness
7.2.1. Choose the most appropriate slots and run the shoulder straps through them. The slots
position should be determined by the height of the child.
C
D
Picture 7.01
Picture 7.02