Motorola solutions HTN9000 User manual

SINGLE-UNIT CHARGER
HTN9000 AND EPNN5115
USER GUIDE
en-US fr-CA es-LA pt-BR zh-TW

1
English
CHARGER: HTN9000D AND EPNN5115B
IMPORTANT SAFETY INSTRUCTIONS
This document contains important safety
and operating instructions. Please read
these instructions carefully and save them
for future reference.
Before using the battery charger, read all the
instructions and cautionary markings on (1) the
charger, (2) the battery, and (3) on the radio using
the battery.
1. To reduce risk of injury, charge only
the rechargeable Motorola Solutions
authorized batteries listed in Table 1.
Other batteries may explode,
causing personal injury and damage.
WARNING
WARNINGS

2
English
WARNINGS (continued)
2. Use of accessories not recommended
by Motorola Solutions may result in risk
of fire, electric shock, or injury.
3. To reduce risk of damage to the
electric plug and cord, pull by the plug
rather than the cord when disconnecting the
charger.
4. An extension cord should not be used unless
absolutely necessary. Use of an improper extension
cord could result in risk of fire and electric shock. If
an extension cord must be used, make sure that the
cord size is 18 AWG for lengths up to 100 feet
(30.48 m), and 16 AWG for lengths up to 150 feet
(45.72 m).
5. To reduce risk of fire, electric shock, or injury, do not
operate the charger if it has been broken or
damaged in any way. Take it to a qualified Motorola
Solutions service representative.
WARNING

3
English
WARNINGS (continued)
6. Do not disassemble the charger; it
is not repairable and replacement
parts are not available. Disassembly
of the charger may result in risk of
electrical shock or fire.
7. To reduce risk of electric shock, unplug the
charger from the ac outlet before attempting any
maintenance or cleaning.
8. This is a Class A product. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.
WARNING

4
English
OPERATIONAL SAFETY GUIDELINES
• Turn the radio off when charging the battery.
• This equipment is not suitable for outdoor use. Use
only in dry locations/conditions.
• Connect equipment only to an appropriately fused
and wired supply of the correct voltage (as
specified on the product). Disconnect from line
voltage by removing main plug.
•The socket outlet to which this equipment is
connected should be close by and easily
accessible.
• In equipment using fuses, replacements must
comply with the type and rating specified in the
equipment instructions.
• Maximum ambient temperature around the power
supply equipment must not exceed 40°C (104°F).
• Output power from the power supply unit must not
exceed the ratings stated on the product label
located on the bottom of the charger.
• Make sure the cord is located where it will not be
stepped on, tripped over, or subjected to water,
damage, or stress.

5
English
CHARGER SPECIFICATION
Input: 14 V , 1 A
Output: 8.4 V , 1.25 A
MOTOROLA SOLUTIONS AUTHORIZED
BATTERIES
The batteries listed in Table 1 are approved for use with the
Single-Unit Chargers in Table 2.
Table 1. Motorola Solutions
Authorized Batteries
Kit (part)
Number Battery Chemistry/Description
HNN9008_R NiMH/High-Capacity
HNN9009 NiMH/Ultra-High-Capacity
HNN9010_R NiMH/Ultra-High-Capacity, Factory Mutual
HNN9011 NiCd/High-Capacity, Factory Mutual
HNN9012 NiCd/High-Capacity
HNN9013_R Lithium Ion/High-Capacity
JMNN4023_R Lithium Ion
JMNN4024_R Lithium Ion/High-Capacity

6
English
Note: In Taiwan, only battery HNN9013D is available.
POWER SOURCES AND MOTOROLA
SOLUTIONS AUTHORIZED TRANSFORMERS
These Class 2 battery chargers should be used with the direct
plug-in, Motorola Solutions authorized transformers listed below:
JMNN4025_R NiMH, Factory Mutual
NNTN5510_R ATEX Lithium Ion, 1480 mAh
PMNN4073_R Lithium Ion, Factory Mutual, IP67
PMNN4074_R Lithium Ion, Non-Factory Mutual, IP67
PMNN4094 Lithium Ion, Non-Factory Mutual, IP67
PMNN4097 NiMH/High-Capacity
PMNN4440 Lithium Ion, Non-Factory Mutual, IP68
PMNN4502 IMPRES Lithium Ion 3000T, IP68
PMNN4511 IMPRES Lithium Ion 2900T, IP68
Table 1. Motorola Solutions
Authorized Batteries (Continued)
Kit (part)
Number Battery Chemistry/Description

7
English
Note: All the transformers listed in Table 2 can also be used with the
HTN9000 charger.
Note: In Taiwan, only kit or power source or transformer 25009297001 is
available.
Table 2. Kits/Power Sources/Transformers
Kit Number Power Source Transformer
(part) Number
AAHTN3000 110–120 Vac
50/60 Hz (U.S. Plug) 2571586S13
AAHTN3001 230Vac (Euro. plug) 2571586S07
AAHTN3002 230Vac (U.K. plug) 2571586S06
HTN3032 230Vac (Argentina plug) 2571586S11
RLN4948 120Vac (U.S. plug) 2580410E01
RLN5255 230Vac (U.K. plug) 2580410E01
RLN5256 230Vac (Euro plug) 2580410E01
PMLN5195 90–264Vac (U.K. plug) 2571886T01
PMLN5196 90–264Vac (Euro plug) 2571886T01
PMLN5197 90–264Vac (U.S. plug) 2571886T01
PMLN5205 90–264Vac (Aus/NZ plug) 2571886T01
WPLN4282 90–264Vac (Brazil plug) 2571886T01
PMTN4024 120 VAC (US/Taiwan Plug) 25009297001

8
English
OPERATING INSTRUCTIONS
Single-unit chargers will charge only the Motorola
Solutions authorized batteries listed in Table 1 on
page 5 Other batteries may not charge.
The battery charger’s pocket will accommodate
either a radio with a battery attached or a battery
alone. Prior to charging a battery with radio, turn
the radio off. To charge a battery, use the following
procedure: (Refer to Figure 1, page 8)
1. Plug the round end of the transformer cord into the
socket on the back of the charger.
2. Plug the transformer into the appropriate ac outlet.
The charger LED will blink green once to indicate
a successful power-up.
3. Insert a battery, or a radio with battery (radio
turned off), into the charger's pocket by:
a. aligning the groove on each side of the battery
with the corresponding raised rail on each side
of the charger pocket.
b. pressing the battery toward the rear of the
pocket