Motorola solutions IMPRES 2 NNTN8845 Manual

1
English
CHARGER: NNTN8845A
IMPORTANT SAFETY INSTRUCTIONS
This document contains important safety and operating instructions. Please read
these instructions carefully and save them for future reference.
Before using the battery charger, read all the instructions and cautionary markings on (1) the
charger, (2) the battery, and (3) the radio using the battery.
1. To reduce risk of damage to the power supply electric plugs and cords, pull
the plug rather than the cord when disconnecting from the AC outlet or the
charger.
2. An extension cord should not be used unless absolutely necessary. Use of
an improper extension cord could result in risk of fire and electric shock. If an extension
cord must be used, make sure that the cord size is 18 AWG for lengths of up to 6.5 feet
(2.0 m), and 16 AWG for lengths up to 9.8 feet (3.0 m).
3. To reduce risk of fire, electric shock, or injury, do not operate the charger if it has been
broken or damaged in any way. Take it to a qualified Motorola Solutions service
representative.
4. Do not disassemble the charger. It is not repairable and replacement parts are not
available. Disassembly of the charger may result in risk of electric shock or fire.
5. To reduce risk of electric shock, unplug the charger power supply from the AC outlet
before attempting any cleaning.
6. To reduce risk of injury, charge only the rechargeable Motorola Solutions authorized
batteries listed in Table 1. Other batteries may explode, causing personal injury and
damage.
7. Use of accessories not recommended by Motorola Solutions may result in risk of fire,
electric shock, or injury.
OPERATIONAL SAFETY GUIDELINES
• This equipment is not suitable for outdoor use. Use only in dry locations and conditions.
• Recommended charger room temperature is 22 °C to 25 °C (71 °F to 77 °F). Room
temperature must not exceed 35 °C (95 °F).
• The radio can be turned ON only when it is transmitting data wirelessly, such as using
Wi-Fi. Otherwise, turn OFF the radio.
• Connect the charger only to an appropriate power supply listed in Table 2.
• The AC outlet to which the power supply is connected must be close and easily
accessible.
• Make sure the power supply cord to the charger is located where it will not be stepped
on, tripped over, or subjected to water, damage, or stress.
• Connect the power supply only to an appropriately fused and wired AC outlet with the
correct voltage, as specified on the product.
• Disconnect from line voltage by removing the power supply from the AC outlet.
!
W A R N I N G
!
English

2
English
• Connect no more than the appropriate number of charger power supplies to a 15 A or
20 A circuit, as limited by any certified power strip being used.
Note: Daisy chaining power strips is NOT RECOMMENDED. Limit circuit loading below
80% of the circuit rating.
CHARGER SPECIFICATION
Input: 14 V , 2.8 A
Output: 8.7 V , 3 A
MOTOROLA SOLUTIONS AUTHORIZED BATTERIES
APX-Series IMPRES 2™ Chargers can charge the batteries listed in Table 1. The batteries
may be attached to a radio or may be stand-alone.
Table 1: Motorola Solutions Authorized Batteries
Motorola Solutions
Part Number Description
NNTN7033 IMPRES™ Li-Ion FM (HazLoc) IP67 4100 mAh
NNTN7034 IMPRES Li-Ion IP67 4200 mAh
NNTN7035 IMPRES NiMH FM (HazLoc) Ruggedized 2000 mAh
NNTN7036 IMPRES NiMH FM (HazLoc) IP67 2000 mAh
NNTN7037 IMPRES NiMH IP67 2100 mAh
NNTN7038 IMPRES Li-Ion IP67 2900 mAh
NNTN7573 IMPRES NiMH Ruggedized 2100 mAh
NNTN8092 IMPRES Li-Ion FM (HazLoc) Ruggedized 2300 mAh
NNTN8182 IMPRES Li-Ion Ruggedized 2900 mAh
NNTN8921 IMPRES 2 Li-Ion TIA4950 (HazLoc) Ruggedized IP67 3700 mAh
NNTN8930 IMPRES 2 Li-Ion TIA4950 (HazLoc) Ruggedized IP67 2700 mAh
PMNN4403 IMPRES Li-Ion IP67 2150 mAh
PMNN4485 IMPRES 2 Li-Ion Ruggedized IP67 2500 mAh
PMNN4486 IMPRES 2 Li-Ion Ruggedized IP67 3400 mAh
PMNN4487 IMPRES 2 Li-Ion Ruggedized IP67 4400 mAh
PMNN4494 IMPRES 2 Li-Ion Ruggedized IP67 5100 mAh

3
English
Note: In Taiwan, only battery PMNN4494A is available.
Charger is certified for UL, CE, and others, only when used with the power supplies listed in
Table 2.
PMNN4504 IMPRES 2 Li-Ion DIVISION 2 (HazLoc) Ruggedized IP67 3400 mAh
PMNN4505 IMPRES 2 Li-Ion DIVISION 2 (HazLoc) Ruggedized IP67 4850 mAh
PMNN4547 IMPRES 2 Li-Ion TIA4950 (HazLoc) Ruggedized IP68 3100 mAh
PMNN4573 IMPRES 2 Li-Ion TIA4950 (HazLoc) Ruggedized IP68 4600 mAh
Table 2: Motorola Solutions Authorized Power Supplies
Motorola Solutions
Part Number Description
25009256001 42 W, 100–240 VAC, Level 41
1. Requires Power Cord 3004209T-series for various world-wide countries.
Note: In Taiwan, only power supply PS000116A01 is available.
25012006001 21 W, 100–240 VAC, Level 51
2571886T01 21 W, 100–240 VAC, Level 41
PS000040A01 36 W, 120 VAC, Low Noise, Level 6
PS000041A01 36 W, 220–240 VAC, Low Noise, Level 5, EU
PS000041A02 36 W, 220–240 VAC, Low Noise, Level 5, UK/HK
PS000041A03 36 W, 220–240 VAC, Low Noise, Level 5, AU/NZ
PS000041A04 36 W, 220–240 VAC, Low Noise, Level 5, AR
PS000041A05 36 W, 220–240 VAC, Low Noise, Level 5, CH
PS000041A06 36 W, 220–240 VAC, Low Noise, Level 5, KR
PS000041A07 36 W, 220–240 VAC, Low Noise, Level 5, BZ
PS000116A01 42 W, 100–240 VAC
Table 1: Motorola Solutions Authorized Batteries (continued)
Motorola Solutions
Part Number Description

4
English
CHARGER OVERVIEW
1. Charger Status LED.
2. Programming/Fleet Management Port - connect to Communication Module in Table 3.
3. USB charging ports. (Output: 5 V/0.5 A)
4. DC Input Socket - connect to power supply in Table 2.
5. Calibration/Reconditioning Switch.
Table 3: Motorola Solutions Communications Modules
Motorola Solutions
Part Number Description
NNTN8870 IMPRES 2 USB Reprogramming and Fleet Management Module
1
2 3 4
5

5
English
OPERATING INSTRUCTIONS
• Batteries charge best at room temperature.
• Batteries may be attached to a radio or stand-alone.
CHARGING PROCEDURE
Power Adapter

6
English
1. Place the APX IMPRES 2 Single-Unit Charger on a flat surface.
2. Firmly insert the power supply barrel connector into the charger DC Input Socket at the
back of the charger.
3. Plug the power supply (power adapter) into a matching power outlet.
4. Upon successful power-up, the pocket LED shows Green for one second. If the LED
does not turn on, check the power supply cord connections.
5. Insert the radio with battery or stand-alone battery into the pocket.
6. When the radio or stand-alone battery is properly seated in the pocket, charging status
will be indicated on the charging indicator LED. If the charging indicator LED does not
indicate start of charging, check radio or stand-alone battery seating in the pocket and
power supply cord connections.
7. The radio or stand-alone battery is ready for use when the LED is Steady Green.

7
English
LED INDICATIONS
Table 4: LED Indications for IMPRES 2 or IMPRES Battery
Status LED Indication
Charger Powering Up Green for approximately one second.
Battery Detected
Battery requires Calibration but Calibration is disabled in
charger:
Alternating Amber and Green for four seconds.
Battery Discharging Steady Amber
Rapid Charging Steady Red
Charged to 90% or more Flashing Green
Charged to 95% or more
Battery requires Calibration but Calibration is disabled in
charger:
Alternating Amber and Green for four seconds then,
Steady Green.
Battery may be nearing End of Service (battery is usable):
Alternating Red and Green
Fault Flashing Red
Standby
• Battery is waiting to rapid charge.
• Battery may be too hot, too cold, or low voltage.
Flashing Amber
Table 5: LED Indications for Other Motorola Solutions
Batteries
Status LED Indication
Charger Powering Up Green for approximately one second.
Battery Detected Steady Red
Rapid Charging Steady Red
Charged to 90% or more Flashing Green

8
English
ADDITIONAL FEATURES AND INFORMATION
The complete online user guide is available through publication part number MN002406A01
at https://businessonline.motorolasolutions.com. This guide provides information on the
APX-Series IMPRES 2 Single-Unit Charger features, including:
• IMPRES 2 Charging Features
• Details regarding charging status and LED indications for various batteries
• Charger Reprogramming
• IMPRES Battery Fleet Management
• USB Accessory Charging
Charged to 95% or more Steady Green
Fault Flashing Red
Standby
• Battery is waiting to rapid charge.
• Battery may be too hot, too cold, or low voltage.
Flashing Amber
Table 5: LED Indications for Other Motorola Solutions
Batteries (continued)
Status LED Indication
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or
registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other
trademarks are the property of their respective owners.
© 2016 and 2020 Motorola Solutions, Inc. All rights reserved.