Neopost ij25 User manual

IJ-25 Getting Started...
Please ensure that you have all components before
starting
Location of installation
This equipment should be installed in close proximity to an easily accessible switched
power supply and telephone socket.
Start by removing the IJ-25 from its packing carton, open the front cover and remove
the white cardboard packing material before unpeeling the protective tape.
Your Carton Contains
1. IJ-25
2. Ink Cartridge
3. Power Supply
4. User’s Guide
5. Getting Started Guide
6. Weighscale
7. Weighscale Cable
8. Modem Cable
9. Self Adhesive Labels
(30 off)
Please retain all packaging for the IJ-25 to be returned in the event of a repair.
Items Sent Separately
Credifon PIN Number & Customised Memory Card with your own message.
Adding Credit to your IJ-25 (see page 24 of the User’s Guide)
Ensure that your IJ-25 is connected to the telephone wall socket by way of the Modem
Cable (as detailed under ‘Connecting the Modem Cable’ section of this document).
In order to add credit to your IJ-25, you will need your Credifon PIN, this will have been
sent to you separately.
Your IJ-25 is programmed with the direct dial Credifon telephone number.
The Credifon Crediting System telephone number must be prexed by the appropriate
outside line digit (for most systems this is a 9 or a 0), if your outside line is routed through
a switchboard (this procedure is detailed on pages 24 - 25 of your User’s Guide).
You are now on your way to crediting your IJ-25.
1. Press the Funds key , the Recredit display will
be observed:
Press to conrm.
2. Enter your Credifon PIN.
3. Enter the credit amount you wish to purchase (e.g.
€20)
(€10 - €500 in units of €10).
Press: , verify the amount before proceeding
(If incorrect, press and start again).
4. Press to conrm.
5. Your IJ-25 will now connect to the Credifon Crediting System - showing
CONNECTING and TRANSACTING displays - and the credit will be added to your IJ-25.
On completion of the crediting procedure, the
following display will be observed:
6. Press to go to Ready mode.
Note:
You will be prompted to connect to the Credifon Crediting System every 90 days. This
allows the An Post to inspect your meter and help prevent possible fraud.
YOU ARE NOW READY TO USE YOUR IJ-25
For further details or in case of difculty, please refer to the User’s
Guide.
{RECREDIT? }
0.00
CREDIFON PIN
----
CREDIT ENTRY
20.00
RECREDIT DONE
20.00
1
2
3
4
6
7
10
8 9
11
5
4142836D/A - 01/02/2015
Neopost Ireland Ltd, - Unit 16, Fonthill Retail & Industrial Park, Dublin 22
Tel:[phone] E-mail: Info @ neopost .ie web: www.neopost.ie

Connecting the Weighscale (Item Nos. 6 & 7 on previous page) (See page 8
of the User’s Guide)
1. Remove the scale from the packaging and place close to the IJ-25.
2. Connect the square plug to the socket marked at the back of the IJ-25.
Connecting the Modem Cable (Item No. 8 on previous page) (See page 24
of the User’s Guide)
1. Locate the modem cable, this has a standard telephone connector on one end.
2. Insert the telephone connector into the telephone wall socket and the small square
plug into the socket marked at the back of the IJ-25.
Connecting to the Power Supply (Item No. 3 on previous page) (See page
6 of the User’s Guide)
The D.C. power unit connects directly to the main power supply socket and is intended
to serve as the device for isolation of the power supply. The IJ-25 is designed to be
continually powered.
1. Connect to your power supply socket.
2. Insert the round plug into the socket marked at the back of the IJ-25.
3. Turn the switch on your power supply socket to the ON position.
4. Press to unlock the IJ-25. This is the factory set PIN, which
can be changed. (see page 19 of the User’s Guide)
The CARTRIDGE INSTALL display will now be
observed:
Fitting the ink cartridge (see pages 16 & 17 of
the user’s Guide)
Note:
Please follow these instructions carefully otherwise your IJ-25 will display an error
message.
1. Raise the IJ-25 front cover.
2. Open fully the Blue Latch to the right.
Remove the ink cartridge from its box and
peel off the Blue Tape seal that protects the
Print Head.
3. Insert the cartridge into the IJ-25
pressing fully home as illustrated, close the
Blue Latch locking the cartridge in place.
Close the top cover and press .
The following display will now be observed
Notes:
a) The ink charging process may take a short while
to complete, during this time the IJ-25 may produce some mechanical sounds,
this is normal.
b) Once installed, do not open the blue latch again until you need to t a new
cartridge.
4. You will now have to produce a test print by inserting
a blank envelope or card, as illustrated.
The following display will now be observed:
Enter the number that corresponds to the straightest
vertical line (for the example above: line 5).
Press .
The message WARNING INSPECTION REQD will now
be observed. This message is displayed because your
IJ-25 requires a crediting transaction.
Press the key.
Preparing your IJ-25 for use
CARTRIDGE
INSTALL?
INSERT ITEM
ALIGNMENT
5
PLEASE
WAIT
WARNING
INSPECTION REQD