VeEX RTU-300 User manual

VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com
QUICK START GUIDE
How to Configure the RTU
Remote Connection, Software Upgrade & Port Configuration
RTU-300/320/600
June 2020 | Rev. A00
P/N: D08-00-036

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 2
Notice:
The information contained in this document is subject to change without notice.
VeEX® Inc. makes no warranty of any kind with regard to this material, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. VeEX shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this
material.
The features or functions described in this document may or may not be available in your test equipment or may
look slightly different. Make sure it is updated to the latest software packages available and that is has any related
licenses that may be required.
For assistance or questions related to this document and procedures, or to get a test set serviced by VeEX or an
authorized service facility, please contact:
VeEX Inc.
Phone: [phone]
E-mail: C[email protected]
Web: www.veexinc.com
©Copyright VeEX Inc. All rights reserved. VeEX, VePAL are registered trademarks of VeEX Inc. and/or its affiliates in
the USA and certain other countries. All other trademarks or registered trademarks are the property of their
respective companies. No part of this document may be reproduced or transmitted electronically or otherwise
without written permission from VeEX Inc.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 3
How to Configure the RTU-300/320/600
Testing with the RTU (Remote Test Unit)
Introduction
The RTU-300/320/600 is a rack mounted 1G-100G Ethernet test head for performance testing and monitoring
Carrier Ethernet and broadband networks. The main application of the RTU-300/320/600 is to be used under the
VeSion™performance testing and monitoring platform, where several RTU-300/320/600 can be added and
operated for service provisioning, service activation testing, and service assurance applications.
Optionally the RTU-300/320/600 can be operated as a stand alone test device through VNC/web remote access. In
this standalone mode, users have access to other interfaces and features that are available such as OTN,
SONET/SDH, and Fibre Channel.
64K-100GE test rates are supported on the same module. These factory-installed hardware options allow flexibility
to fit any additional application at a later time. For example, the addition of a second RTU-320 or RTU-600 module
can be installed concurrently on the same test platform.
RTU-320 Test Ports:
2 x SFP+ for Ethernet, OTN & SONET/SDH
2 x RJ45 for Ethernet
2 x BNC for E1/DS3
1 x RJ45 for E1/DS1
1 x SMA for Clock Source
RTU-600 Test Ports:
1 x QSFP28 for 100GE and OTU4
1 x QSFP+ for 40GE, OTU3
1 x External Clock Interface
Space efficient 1U rackmount with built-in, dual power switching matrix ensures continuous operation if the main
power supply fails.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 4
Dual power options with back up DC (15V or 48V):
Connecting to the Unit
There are two ways to connect to the unit: via the serial port or via the Ethernet port using the ReVeal Probe
Configurator Tool (with the factory default IP address 192.168.1.1 or when it is a known IP address to the user). If
the IP address is unknown, the serial port must be used to assign/verify an IP address. Connect via VNC or VeSion
to configure the unit and run tests.
1. Download the required software package from the VeEX Software Download Page:
https://www.veexinc.com/en-us/Support/Software.
Use the unit’s serial number to find the correct file.
2. Launch the ReVeal Probe Configurator Tool. Select the correct port to connect via serial connection on your
PC. In this case, we are using COM3. Select the Probe Type as RTU-300. Click Open.
Power
Button
Serial
Port
Ethernet
Port
15
V
48V
Unit Serial
Number

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 5
Note: If you are using Putty for example, use the following settings to connect to the RTU (115200 baud rate).
3. The Status window will indicate that the serial port is opened. Once the port is open, click Connect.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 6
Before getting prompted to enter the S/N, the RTU must be powered off, then on again as stated in the Status
window. Enter the unit’s serial number when the dialog box appears and click Ok.
4. The probe’s default IP address settings will be populated after the serial number is entered. The VeSion server
IP address (Probe Server IP) must be assigned in order to use VeSion to log in to the unit and launch tests. The
Local IP address should be modified according to your network IP settings –VNC will use this IP address to log
in to the unit.
5. Make sure that Probe Server Port is 12320.
Note: The VeSion server IP address, the RTU-320 Probe Number, and VeSion TCP Port number need to be configured in
order for the VeSion system to talk to the RTU.
6. Modify the IP address as required under Local IP/Local Subnet/Local Gateway. Click Apply.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 7
RTU-300/320/600 System Settings and Operating Mode Configuration
via ReVeal Probe Configuration Tool
To configure RTU operating mode follow these steps:
1. Use the RTU-320 section to select RTU-300/320 Operation Mode:
•VeSion –Operate via VeSion management tool
•SCPI –Operate via web browser or VNC
Note: RTU-600 module supports only operation via web browser or VNC.
2. When the desired Operating Mode has been selected click Apply. The status window will indicate that the
configuration has changed and the probe will be rebooted.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 8
Web Remote Access Menu/VNC (Standalone Mode)
In order to operate the RTU-300/320/600, launch a new web browser window and type the RTU-300/320/600
management IP address. Login using appropriate credentials (Default User ID –admin and password - veexinc).
When operating the RTU via web browser, multiple options are available under the Web Remote Access menu:

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 9
•Account –Manage user accounts. Add, Edit or Delete accounts.
•Profile –Manage test profiles.
•Remote Control –Load test applications.
•Manual –Open the RTU-300 user manual.
•Results –Manage test results.
•Screen Shots - Manage screen shots taken from the RTU-300.
•Configuration –Configure system settings such as Local IP, Subnet, etc. and
RTU300 settings such as Operating Mode to be operated via VeSion or web
browser.
•Platform Upgrade –Perform a platform upgrade.
•Module Upgrade –Perform a module upgrade.
RTU-300/320/600 System Settings and Operating Mode Configuration
via Web Remote Access/VNC (Standalone Mode)
To configure RTU operating mode and other system and module parameters click Configuration under the Web
Remote Access options and follow the next steps:
3. Use the System Setting section to configure Local IP Address, Subnet, Gateway.
4. Use the RTU-320 Settings section to select RTU-300/320 Operation Mode:
•VeSion –Operation via VeSion management tool.
•SCPI –Operation via web browser or VNC.
Note: RTU-600 module supports only operation via web browser or VNC.
5. When the desired Operating Mode has been selected click Apply and then Reboot. The new configuration will
take effect after the unit reboots.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 10
RTU Software Upgrade
Upgrading the RTU via Web Remote Access Menu/VNC (Standalone Mode)
Platform Upgrade
Note: The Platform software upgrade process is intrusive and any test will be interrupted; make sure to save any
configuration or test results before proceeding.
Click Platform Upgrade under the Web Remote Access option and perform the following steps from the Platform
Upgrade tab:
1. Download and unzip the required software from https://www.veexinc.com/en-us/Support/Software. Make
sure to enter the RTU-300/320/600 serial number to find the correct file.
2. The Platform SW (install_rtu300_platform.sh) has to be upgraded first followed by the module software
upgrade (install_rtu300_rtu320.sh/install_rtu300_100g.sh). However, if only the module SW has to be
upgraded, there is no need to upgrade the platform.
3. Browse the software image file by clicking the select file button.
4. When the file is selected, click Upload to send the file to the RTU-300/320/600.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 11
5. Once the upload process is completed and file verification is successful, click Upgrade.
6. Users will be asked to confirm if the upgrade procedure should continue, as a reboot will be performed at the
end of the process.
7. When the reboot process has been completed, log back in to the RTU-300/320/600 and verify that the platform
software version was updated on the home page.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 12
Module Upgrade
Note: The module software upgrade process is intrusive, and any test will be interrupted; make sure to save any
configuration or test results before proceeding.
Click Module Upgrade under the Web Remote Access options and perform the following steps from the Module
Upgrade tab:
1. Download and unzip the required software from https://www.veexinc.com/en-us/Support/Software. Make
sure to enter the RTU-300/320/600 serial number to find the correct file.
2. Browse the software Image file by clicking select file.
3. When the file is selected, click the Upload button to send the file to the RTU-300/320/600.
4. Once the upload process is completed and file verification is successful, click Upgrade.
5. When the reboot process has been completed, log back in to the RTU-300/320/600 and verify that the module
software version was updated on the home page.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 13
Loading a Test Application via Web Remote Access/VNC (Standalone
Mode)
1. Log in to the RTU using VNC. Type the IP address configured previously after launching the VNC app. The default
password is pass1. To start testing, load the required test application using the New button in Port Group 1 or
Port Group 2.
.
2. Select the desired test application and press OK to launch it.
Follow the TX320s and TX300-100G User Manual instructions to set up a Loopback, Throughput, RFC-2544 or V-
SAM Test. You can find them in the downloads section of the product page at https://www.veexinc.com.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 14
Using VeSion to Configure the RTU User Access
This section will focus on creating new users and assigning credentials to tester types in VeSion, a web-based
management tool.
1. Launch your web browser and type the VeSion server IP address. Type your User ID and password to login.
2. Manager level credentials display System Configuration settings as shown below.
3. Under the System Configuration menu, the user can configure the RTU test ports and IP settings.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 15
4. Tester level credentials enable users to run tests. Privileges are limited to running tests and viewing
configurations only.
5. Notice the difference between User access privileges and Manager level privileges as shown below.
Manager level privileges
User level privileges

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 16
Adding/Removing Users
1. Click on System Configuration >User & Group >User
A list of current users and their group will be displayed.
2. To create a user with Tester privileges, testing and viewing results only:
•Click on Add New. Select Tester from the Group drop-down menu.
•Input the Name, User ID, and Password, and click Save.
•To test the newly created user, log out and log back in using these new credentials to make sure only
Tester privileges are available.
Configuring the Test Ports
This section will focus on configuring the physical test ports. In the System Configuration menu, the user can
configure the RTU test port and IP settings.
1. Log in with a user that has Manager privileges. Click System Configuration > Server & Device.All available sub-
menus are shown below.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 17
2. Make sure the RTU-300 is selected if other devices are also being used by this VeSion server. Select a module
(Slot) as shown below and a Test Mode.
The following test modes are available:
•1GE Dual Port L2 & L3 Testing –Enables running the 1GE Loopback, Throughput, V-SAM, and RFC2544
tests on both ports
•1GE Dual L4 Stateful TCP Testing –Enables running the 1GE V-PERF test on both ports
•1GE Dual L4 Stateful TCP Testing + L2 & L3 Testing –Enables running 1GE Loopback, Throughput, V-
SAM, and RFC2544 tests on one port and 1GE V-PERF test on another

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 18
•10GE Dual Port L2 & L3 Testing –Enables running 10GE Loopback, Throughput, V-SAM, and RFC2544
tests on both ports
•10GE Dual L4 Stateful TCP Testing –Enables running 10GE V-PERF test on both ports
•10GE Dual L4 Stateful TCP Testing + L2 & L3 Testing –Enables running 10GE Loopback, Throughput, V-
SAM, and RFC2544 tests on one port and 1GE V-PERF test on another
•1GE/10GE Dual Port L2 & L3 Testing –Enables running 1GE Loopback, Throughput, V-SAM, and
RFC2544 tests on one port and 10GE Loopback, Throughput, V-SAM, and RFC2544 tests on another
3. Scroll down the page to modify any Test Port IP settings. Change the Port Settings, IP address information,
VLAN ID, Priority bit as required. Click Save.
While the changes are taking places, you will see In Progress status for Port Configure. When the configuration
is done, the Succeeded status should appear instead.

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 19
Click on the Network Status tab to verify that the IP Configuration status is OK. It should say PASS for IP & Gateway.
Running a Throughput Test via VeSion
05
05
◼Run RFC-2544 Throughput
Test
◼Run V-SAM Test
Core
Run Layer 3
Throughput
and V-PERF
Test

QUICK START GUIDE: RTU-300/320/600
VeEX Inc. 2827 Lakeview Court, Fremont, CA 94538 USA Tel: [phone] Fax: [phone] www.veexinc.com [e-mail] 20
To start the Throughout Test via VeSion follow the next steps:
1. From the home page, click On-Demand Test.
2. Make sure the right RTU-300 is selected if other devices are also being used by this VeSion server. Select the
test ports to be used on the left-hand side. Toggle in between the Port 1 & Port 2 configuration using the tabs
as shown below.
3. Select Throughput from the Test Type drop-down menu at the bottom.