aivituvin AIR 18 User manual

INSTRUCTION
MANUAL
AIR 800
www.aivituvin.com
X
AIR 34
AIR 18

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’ s instructions as this could void the product
warranty.
01

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
16PCS+1 spare
P1 P2
P3 P4
P5
02
M3.5x25mm SCREW
M3.0x16mm SCREW
P6
18PCS+1 spare
M3.5x40mm SCREW
1 PC
M3.0x10mm SCREW
2PCS+1 spare
2PCS
22PCS+1 spare
P7
Chewing Toy for gift
Latch
1 PC

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC
1PC
Left Panel
Front Panel -Upper Front Panel -Down Back Panel -Upper
Right Panel
The Middle Tray Ramp Supporting Layer
Back Panel -Down
Wood Layer-Up &Down
2PCS

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
MNO
04
2PCS
1PC
1PC
Top Cover Panel Divider The Bottom Tray
Casters without brake
Ramp -Upper
1PC 1PC
1 PC
Ramp -Down
P Q R
1PC
2PCS
Folding Metal feeder
Brake Casters
2PCS
Tray Supporting bar

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
S
05
Bottom Wire Netting
1PC

PRODUCT ASSEMBLY
01
02
06
①Attach Part C by 2XP1 screws each side.
Attach the back first, screw back panel Part D with right panel
Part F, left panel Part E by 2xP1 screws each side.
F
P1X4
K
D
E
②Then screw the divider Part K to Part C by 1xP1 screw.
C
P1X2
P1X
2
P1X
1

PRODUCT ASSEMBLY
03
04
07
①Attach the front panel Part B to the sides by 4xP1 screws.
①Put the tray supporting bars 2 part Q into the side groove.
P1
X4
P1
X2
Put inside the bottom wire netting Part S to be UPWARDS
to seperate the urine & poop.
②
③Put Part H inside the cage as show on picture.
SH
②Attach the front panel Part A by 4xP1 screws.
③Then screw the other side of divider part Kto the front by
1XP1 screw.
P1X1
P1X2
A
Qx2
B

PRODUCT ASSEMBLY
05
06
08
Slide in the middle tray Part G and the bottom tray Part L.
Screw the down ramp Part N to the tray surpporting bar Part
Q as show on picture by 4xP3 screws.
L
G
P3X4
N

PRODUCT ASSEMBLY
07
08
09
Put the ramp supporting layer Part I and another wood layer Part
H inside the cage as show on picture.
①Screw the upper ramp Part M to the layer by 4xP3 screws.
H
P3X4
M
I
②Screw the metal feeder Part R to the right panel Part F by 2xP4
screws.
③Put the chewing toy P7 inside the cage anywhere you want.
P7X1
Rx1
P4 X2

PRODUCT ASSEMBLY
09
10
10
Screw the hook P5 to the Part E, tie the rope on one side of roof
and the other side of hook to make the roof open.
Attach top cover panel Part J to the hutch by 6xP3 screws.
P3 X6
J
P5X1

PRODUCT ASSEMBLY
11
12
11
Screw two casters without brake Part O to the front of hutch legs
by P2x4 each.
①Screw 1pc of latch P6 to the left panel Part E by 4xP3 screws.
P3 X4
②Screw 1pc of latch P6 to connect the top cover and front panel
by 4XP3 screws.
P6X1
P3 X4
P6X1
Ox2
P2X8

PRODUCT ASSEMBLY
13
12
Screw two brake casters Part P to the back of hutch legs by
P2x4 each.
Px2
P2X8

HELP CENTER
[email protected]
Question about your product? we're here to help contact us via
Returns & Refunds
?
Product AssemblyOrders FAQProduct inquiry
THANK YOU
Thanks for your support to Aivituvin.
Your satisfaction is our #1 priority.
Once the items are received, opened, and deemed to be faulty
or other problems.
Pls contact us at [email protected] for the solution.
We will feedback to you within 24 hours.
If you are happy with the shopping ,welcome to share photos
and thoughts with others .
www.aivituvin.com
13

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.