Oxgard CUBE ?-04 Series Instruction sheet

VOZROZHDENIE, LLC
OKPD 2 26.30.50.110
TU 26.30.50-007-33120038-2017
APPROVED
VZR.235900.000 LU
TURNSTILE
MODEL CUBE С-04
С-04-c, С-04-К, С-04-Кc, С-04-H, С-04-Hc, С-04-НК, С-04-НКc
VZR.235900.000 IG
INSTALLATION GUIDELINES
Sheets 40
2019

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
2
CONTENTS
1. General Guidelines .........................................................................................................................4
2. Safety Precautions..........................................................................................................................5
3. PreparING THE PRODUCT for Installation ....................................................................................6
3.1 Procedure for transporting the product to installation site.......................................................6
3.2 Product unpacking rules.........................................................................................................6
3.3 Product inspection rules.........................................................................................................6
3.4 Requirements for the product’s installation site.......................................................................8
3.5 Procedure for checking installation site for compliance...........................................................9
4. Mounting and Dismounting of THE PRODUCT........................................................................... 10
4.1 Required Equipment.............................................................................................................10
4.2 Mounting the Product ...........................................................................................................11
4.3 Dismounting the product.......................................................................................................15
5ConnectiNG and AdjustING THE PRODUCT ...............................................................................16
5.1 Power supply connection......................................................................................................19
5.2 Control Panel Connection.....................................................................................................19
5.3 Connecting Access Monitoring and Control System (optionally)........................................... 20
5.4 Connecting control panel to AMCS controller .......................................................................23
5.5 Card Collector Connection....................................................................................................27
6Integrated Inspection....................................................................................................................32
6.1 Inspecting and checking the product’s readiness for use......................................................32
7commissioning THE Mounted PRODUCT....................................................................................33
APPENDIX A — Short description of data transfer bus CAN2.0.......................................................34
APPENDIX B — Layout of mounting holes in relation to turnstile external dimensions................ 35
APPENDIX C — Turnstile Connection Diagram................................................................................. 36
APPENDIX D — STRUCTURAL FLOWCHARTS for AMCS using Card collector............................. 37

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
3
These Installation Guidelines (IG) apply to Turnstile Oxgard Cube С-04 and
its modifications (hereinafter referred to as “the product”). The firmware version of
the product: FW v2.2
These Installation Guidelines specify rules and procedure for installation and
startup of the product.
Prior to installing the product, the personnel should additionally read
Operational Manual VZR.235900.000 OM.
Due to continuous work on the improvement of the product, its design might
be subject to changes that have not been reflected in this IG revision.
A card collector can be integrated into the turnstile’s design.
The following abbreviations have been adopted for use herein:
OM — Operational Manual;
IG — Installation Guidelines;
PSU — Power Supply Unit;
RC panel — Remote Control Panel;
AMCS — Access Monitoring and Control System;
SAFAS — Security and Fire Alarm System;
NC — Normally Closed Connection;
NO — Normally Open Connection.

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
4
1. GENERAL GUIDELINES
When assembling and installing the product, please consider all the
recommendations and guidelines detailed herein for overall safety reasons.
Prior to starting the installation works, fully de-energize the product.
DO NOT:
INSTALL THE POWER SUPPLY UNIT INSIDE THE TURNSTILE CASING,
BECAUSE THIS MAY CAUSE ELECTROCUTION.
INSTALL THE TURNSTILE ANYWHERE OUTSIDE DRY AND HEATED
ROOMS.
OBSTRUCT OR ACCELERATE THE MOVEMENT OF THE TURNSTILE
BARS.
USE FOR CLEANING ANY PASTES OR FLUIDS THAT ARE CHEMICALLY
AGGRESSIVE TO MATERIALS OF THE HOUSING.

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
5
2. SAFETY PRECAUTIONS
When carrying out the installation, “Rules for Technical Operation of
Consumers' Electrical Installations” and “Safety Rules for Operating Consumers'
Electrical Installations” shall be respected.
Qualified personnel duly trained for operating electrical appliances and
instructed on the safety rules to follow when working with electrical installations of
up to 1000V, shall be permitted to install the product.
ATTENTION:FAILURE TO COMPLY WITH SAFETY
REQUIREMENTS SPECIFIED IN THIS SECTION MAY CAUSE DAMAGE TO
HUMAN LIFE AND HEALTH AND FULL OR PARTIAL LOSS OF THE
FUNCTIONABILITY OF THE PRODUCT AND / OR AUXILIARY EQUIPMENT.
ATTENTION:IN CASE OF FAILURE TO COMPLY WITH SAFETY
REQUIREMENTS SPECIFIED IN THIS SECTION, THE MANUFACTURER SHALL
NOT BE HELD LIABLE FOR DAMAGE TO HUMAN LIFE AND HEALTH, AND
FULL OR PARTIAL LOSS OF THE FUNCTIONABILITY OF THE PRODUCT
AND / OR AUXILIARY EQUIPMENT, AND TERMINATE THE PRODUCT’S
WARRANTY.

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
6
3. PREPARING THE PRODUCT FOR INSTALLATION
3.1 Procedure for transporting the product to installation site
The product in factory packaging can be transported by air, closed motor and
railroad transport means when fitted with protection against direct exposure to
precipitation and dust without distance limitation.
After shipment under subzero temperature, the product shall be kept in a
room under normal climatic conditions during 12 hours to avoid moisture
condensation.
When carrying out handling operations, safety requirements shall be
observed.
3.2 Product unpacking rules
3.2.1 Inspect the package externally. The package shall have no visible
damages.
3.2.2 Open the transportation box, unpack it and examine the product
composition:
1) turnstile stand;
2) RC panel with cable;
3) latch keys (4 pcs).
3.3 Product inspection rules
3.3.1 Check the completeness of the set.
Check the completeness of the set in accordance with Datasheet
VZR.235900.000 DS.

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
7
3.3.2 Inspect the product externally. The product shall have no visible
damages.
3.3.3 Should any damages be revealed, prepare a Damage Claim.
3.3.4 Figure 1 – Turnstile’s overall dimensions.
Figure 1 – Turnstile’s overall dimensions

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
8
3.4 Requirements for the product’s installation site
ATTENTION:TO PREVENT THE TURNSTILE SWINGING AND (OR)
TILTING IN THE COURSE OF OPERATION, INSTALL IT SECURELY. IN CASE
OF TURNSTILE INSTALLATION ON LOW-STRENGTH FLOOR, TAKE
MEASURES TO FLOOR STRENGTHENING ON INSTALLATION SITE.
Figure 2 – During the installation of the turnstile, possible free travel of the
arm should be considered. In “STOP” mode, it makes 6 degrees on each side.
Figure 2 - Possible free travel of the arm in “STOP” mode
6 deg

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
9
3.5 Procedure for checking installation site for compliance
ATTENTION: PASSAGE ZONES SHALL BE PROVIDED TO ALLOW
RECORDING OF PASSAGES DURING TURNSTILE OPERATION UNDER AMCS
CONTROL AND TO AVOID UNAUTHORIZED PASSAGES.
3.5.1 Figure 3 – Arrangement of turnstile’s passage zone and
instructions for orienting the product.
Recommended diagram
Not recommended diagram
Figure 3 - Turnstile passage zone arrangement.
1 - barrier
50 mm max
200 mm min

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
10
4. MOUNTING AND DISMOUNTING OF THE PRODUCT
4.1 Required Equipment
The equipment used during turnstile installation:
1) electric puncher;
2) 10mm dia solid-carbide drill for drilling holes in the floor for anchors (recommended
anchor with screw type FH 10/10 SK);
3) Allen key S5;
4) straight-blade screwdriver;
5) plumb or level;
6) steel pads for turnstile alignment;
7) round file;
8) side cutting pliers.

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
11
4.2 Mounting the Product
ATTENTION: PLEASE READ THIS SECTION THOROUGHLY PRIOR
TO MOUNTING THE PRODUCT.
Figure 4 – Turnstile’s main panels
Figure 4 – to access all required turnstile assemblies, the turnstile should be
partially disassembled – dismounting of the card collector containers (1), the
turnstile top (3) and the side covers (2), as specified in OM Section 3.5.
1 – card collector container;
2 – side cover; 3 – top cover;
4 – barrier arm assembly

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
12
4.2.1 Prepare a horizontal platform on the turnstile installation site.
4.2.2 Provide a cable conduit or a cable channel from the platform to
where the PSU and RC panel will be installed and, where necessary, to AMCS and
SAFAS connection location.
4.2.3 Turnstile’s installation site.
Figure 5 – prepare 6 holes, 11 mm diameter, in the floor for two turnstile
stand anchors.
Figure 5 - Turnstile stands
The layout of mounting holes in relation to the turnstile external overall
dimensions is shown in Appendix B.
Embedded hole depth, 120 mm, shall exceed the anchor length by 5 mm.
Insert the anchors into the holes.
Figure 6 – Turnstile’s installation dimensions.
1 - turnstile fixing holes;
2 - hole for cable input

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
13
Figure 6 – Turnstile’s installation dimensions
4.2.4 Figure 6 – wire the cable through the hole (1) in the bottom plate
of the turnstile stands.
4.2.5 Route the RC panel’s cable, PSU’s cable, and, where provided,
AMCS and SAFAS’ cables in the cable conduit or cable channel.
4.2.6 Install the turnstile on the prepared platform.
4.2.7 Pull the RC panel and PSU cables, and, where necessary, AMCS
and SAFAS cables into turnstile housing.
Fix the cables using cable ties.
1 – cable input holes
6 holes

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
14
Figure 7 - routing of cables (1) is indicated with dashed lines, the cable input
hole under the top cover (2).
Figure 7 – Routing of control and power supply cables
1 -cable routing locations;
2 – cable input hole

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
15
4.2.8 Match the holes in the turnstile stands with anchors in the floor.
Check the verticality of the installation in 2 planes; where necessary, use
steel pads of the required thickness for correct installation of the turnstile.
Fix the turnstile stands using 6 screws, turning them into corresponding
anchors and using the wrench or spanner keywith a nut width across flats of 10 mm.
Figure 4 - Install the side (2) and top (3) covers, the turnstile card collector
containers (1).
4.2.9 Remove the protective film from the turnstile housing.
4.3 Dismounting the product
4.3.1 Dismounting of the product when sending it for verification and
repair shall be carried out in the following manner:
1) switch off the power supply of the product;
2) disconnect the product from the power supply;
3) disconnect the product’s cable part from the auxiliary cables;
4) dismount the product from the installation site.
4.3.2 Prior to packaging, remove dust and any contaminations from the
product.
4.3.3 Pack the product into the packing box.

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
16
5 CONNECTING AND ADJUSTING THE PRODUCT
APPENDIX C - Turnstile Connection Diagram. PSU, RC panel and AMCS
shall be connected using the motherboard.
Figure 8 - Layout of boards under top cover on turnstile stand.
Figure 8 - Layout of boards under top cover
1 - Display Control Board;
2 - Card Collector Control Board;
3 - Encoder Board;
4 - Controller Installation Location;
5 - Motherboard;
6 - Control Mainboard;
7 - Card Collector;
8 - Readers

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
17
For turnstile connection and access to all required contacts, the top cover
shall be removed.
To do that, use the key to open an remove the both containers located inside
the turnstile stand, then release 4 mounting studs of the top cover (Figure 9 - 1) and
remove the cover in the shown direction.
Figure 9 - Dismounting of turnstile top cover
1 – cover mounting studs

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
18
Figure 10 - The appearance of the motherboard and the layout of connectors
for PSU, RC panel, AMCS and SAFAS connection are depicted. Motherboard
location (Figure 8 - 5).
Figure 10 - Motherboard appearance
The turnstile’s modes of operation with different positions of jumpers on the
mainboard are detailed in Table 1.
Table 1 Turnstile’s mode of operation
Jumper positions Turnstile’s mode of operation
Potential
Mode
Х1 “On” position Potential Mode (p. 5.3)
Х1 “OFF” position Pulse mode (p. 5.3)
Remont
Control
Х3 “On” position
The turnstile does not respond to panel’s
commands, the status of buttons is transmitted to
the outputs OUT1 through OUT 3 (para 5.4)
Х3 “OFF” position
The turnstile is controlled by the panel, the status
of buttons is transmitted to the outputs OUT1...
OUT 3 (para 5.4)

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
19
5.1 Power supply connection
DO NOT:
USE POWER SUPPLY UNITS WITH AN OUTPUT CURRENT OF LESS THAN
3.0 A.
ENERGIZE THE TURNSTILE USING A POWER SUPPLY CABLE WITH A
CROSS SECTION OF LESS THAN 1.5 MM2WITH THE FEEDER CABLE
BEING MORE THAN 10M LONG – A 2.5 MM2CROSS-SECTION CABLE IS
RECOMMENDED.
ATTENTION: INSTALLING THE POWER SUPPLY UNIT AT A DISTANCE
OF OVER 25 M FROM THE TURNSTILE IS NOT RECOMMENDED.
The turnstile is powered by a 12 VDC unit. Max consumption – 3.0 A.
PSU shall be selected based on these parameters.
Also, it should be considered that when increasing the feeder cable length,
the voltage drop increases (operating voltage range is specified in Operational
Manual VZR.235900.000 RE).
Install PSU in a location easy to access for the operator.
Connect PSU cable to the group of contacts +12U_IN and GND_IN on the
motherboard. Connect PSU’s (+) and (-) contacts to (12V_IN) and (GND_IN)
contacts accordingly.
Make sure the cable is secure.
5.2 Control Panel Connection
Connect RC panel to the group of contacts Pult on the motherboard.
Labeling of contacts: 12V, CL, CH, GND.

VZR.235900.000 IG
Cube С-04 Turnstile
Installation Guidelines
20
The RC panel shall be connected using the labeling of contacts in Table 2.
Table 2 - Labeling of contacts for RC panel connection
Labeling of contacts Wire color
12V Red
CL Yellow
CH Green
GND Blue
5.3 Connecting Access Monitoring and Control System (optionally)
Connect AMCS controller to the group of contacts Control on the
motherboard.
Labeling of contacts: LEFT, RIGHT, STOP, GND. Purpose of contacts is
specified in Table 3.
Table 3 - Purpose of AMCS contacts
Labeling of contacts Purpose of contacts
LEFT, RIGHT left/right single passage
(lowest priority)
STOP no passage is allowed (“Stop” mode)
(highest priority)
GND common contact
Inputs for AMCS connection differ by priorities:
1) STOP input is of the highest priority. When closing this input to GND contact, the turnstile
switches to “Stop” mode and does not respond to other effects;
2) LEFT and RIGHT are of equal low priority and include the single passage in one or other
direction. If both inputs are closed, the passage is allowed in the direction, under which the
input was closed first. In case no passage was performed, the turnstile switches to “Stop”
mode automatically after 5 seconds.