Oxgard CUBE C-10 User manual

VOZROZHDENIE LLC
OKPD 2 26.30.50.110
TU 26.30.50-007-33120038-2017
APPROVED BY
VZR.249600.000LU
FULL HEIGHT ROTOR TURNSTILE
CUBE C-10 MODEL
VZR.249600.000IM
INSTALLATION MANUAL
48 sheets
2021

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
2
TABLE OF CONTENTS
1General instructions....................................................................................................................... 4
2Safety precautions.......................................................................................................................... 5
3Preparing the product for installation ........................................................................................... 6
3.1 Procedure for transporting the product to the installation place .............................................. 6
3.2 Rules for unpacking the product............................................................................................. 6
3.3 Rules for visual inspection of the product ............................................................................... 7
3.4 Product installation place requirements.................................................................................. 8
3.5 Procedure for checking compliance of the installation place................................................... 9
4Product installation and dismantling........................................................................................... 10
4.1 Equipment required.............................................................................................................. 10
4.2 Product installation............................................................................................................... 11
4.3 Dismantling the product........................................................................................................ 23
5Connecting and setting the product............................................................................................ 24
5.1 Power connection................................................................................................................. 29
5.2 Control panel connection...................................................................................................... 29
5.3 Access control and management system connection (optional)............................................ 33
5.4 Control panel connection to the ACS controller .................................................................... 35
6Comprehensive inspection .......................................................................................................... 39
6.1 Visual inspection and verification of the product readiness for use....................................... 39
7Acceptance of the installed product............................................................................................ 40
APPENDIX A —Brief description of CAN2.0 data bus...................................................................... 41
APPENDIX B —Assembly diagram.................................................................................................... 42
APPENDIX C —Position of mounting holes relative to the external dimensions of the turnstile . 44

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
3
This Installation Manual (IM) applies to Oxgard Cube C-10 full height rotor
turnstile and its variants (hereinafter referred to as the product). Product firmware
version:
FC C-10
IM defines rules and a procedure for installation and commissioning of the
product.
Before installing the product, please read the Operation Manual
VZR.249600.000 OM as well.
Due to constant work on improving the product, changes to its design may
be made, which are not represented in this IM revision.
The following abbreviations are used in this document:
OM —Operation Manual;
IM —Installation Manual;
PSU —power supply unit;
CP—control panel symbol;
BCP 01 —basic control panel;
UCP 02 —universal control panel;
ACS —access control system;
SFAS —security and fire alarm system;
NC —normally closed connection;
NO —normally open connection.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
4
1 GENERAL INSTRUCTIONS
For general safety when assembling and installing the product, take into
account all the recommendations and instructions contained herein.
Before starting installation work, completely de-energize the product.
DO NOT:
PERFORM WORK WHEN THE TURNSTILE POWER IS ON. FAILURE TO
COMPLY WITH THESE SAFETY REQUIREMENTS CAN RESULT IN DEATH
AND DAMAGE TO HEALTH, COMPLETE OR PARTIAL LOSS OF
PERFORMANCE OF THE PRODUCT AND/OR AUXILIARY EQUIPMENT.
REMOVE THE BRACKET FROM ITS MOUNTS WITH ROTOR POSITION
SENSOR. OTHERWISE, THE MANUFACTURER WILL TERMINATE PRODUCT
WARRANTY.
APPLY PASTES AND LIQUIDS CHEMICALLY AGGRESSIVE TO
MATERIALS OF THE HOUSING WHEN CLEANING THE PRODUCT.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
5
2 SAFETY PRECAUTIONS
Installation should be carried out with observance of “Regulations for
Operation of Consumer Electrical Installations” and “Safety Regulations for
Operation of Consumer Electrical Installations”.
The product shall only be installed by qualified personnel trained in
handling of electrical devices and instructed on safety precautions when handling
the electrical installations with voltages of up to 1000V.
ATTENTION: FAILURE TO COMPLY WITH THE SAFETY
REQUIREMENTS SPECIFIED IN THIS SECTION CAN RESULT IN DEATH AND
DAMAGE TO HEALTH, COMPLETE OR PARTIAL LOSS OF PERFORMANCE
OF THE PRODUCT AND/OR AUXILIARY EQUIPMENT.
ATTENTION: MANUFACTURER WAIVES ANY RESPONSIBILITY
FOR DEATH AND DAMAGE TO HEALTH, COMPLETE OR PARTIAL LOSS OF
PERFORMANCE OF THE PRODUCT AND/OR AUXILIARY EQUIPMENT IF
USER FAILS TO COMPLY WITH THE SAFETY REQUIREMENTS SPECIFIED
IN THIS SECTION, AND ALSO VOIDS THE PRODUCT WARRANTY.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
6
3 PREPARING THE PRODUCT FOR INSTALLATION
3.1 Procedure for transporting the product to the installation place
The product in the original package can be transported without range
limitation by air, enclosed road and rail transport provided it is protected against
direct exposure to precipitation and dust.
Loading and unloading operations should be carried out in compliance with
safety regulations.
3.2 Rules for unpacking the product
3.2.1 Perform visual inspection of the packaging. There should be no
visible damage on the package.
3.2.2 Open the transportation boxes (Box 1, Box 2), unpack and check
completeness of the product:
1) fixed fencing panel parts;
2) moving fencing elements parts (rotor gate);
3) fixed fencing elements parts:
4) upper module parts;
5) actuating mechanism;
6) CP with cable;
7) keys for door lock (4 pcs.);
8) shipping documentation.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
7
3.3 Rules for visual inspection of the product
3.3.1 Check completeness of the product.
Completeness shall be checked according to the Logbook
VZR.249600.000 (LB) and packing list placed in boxes.
3.3.2 Visually inspect the product. There should be no visible damage
on the product.
3.3.3 If any damage is found, prepare a Claim Report.
3.3.4 Figure 1 –overall dimensions of the turnstile.
Figure 1 –Overall dimensions of the turnstile

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
8
3.4 Product installation place requirements
ATTENTION: TO AVOID WAVING AND/OR OVERTURNING DURING
OPERATION, INSTALL THE TURNSTILE SECURELY. IN CASE OF PRODUCT
INSTALLATION ON LOW STRENGTH FLOOR - TAKE MEASURES FOR
FLOORS STRENGTHENING IN THE PLACE OF INSTALLATION.
Initial state of the turnstile is closed (the turnstile is closed for passage in
both directions).
Figure 2 –initial position of the product flaps.
Figure 2 –Initial position of the flaps
The specified option is determined by the rotor shaft orientation upon its
installation during the turnstile installation.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
9
3.5 Procedure for checking compliance of the installation place
The turnstile by resistance to climatic impact belongs to modification U2 as
per GOST 15150-69 (for outdoor operation).
The turnstile protection class is IP-54.
When selecting the turnstile installation place take into account permissible
operating ambient temperatures from –40 °С to +50 °С and relative air humidity
up to 95 %.
When selecting the control panel installation place take into account
permissible operating ambient temperatures from +1 °С to +55 °С and relative air
humidity up to 80 % at the temperature of +25 °С.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
10
4 PRODUCT INSTALLATION AND DISMANTLING
4.1 Equipment required
Equipment to be used for the turnstile installation:
1) electric perforating machine
2) 18 mm carbide drill bit for drilling anchor holes in the floor (we recommend to use the
sleeve anchor with the bolt of FH 12-S 18/10);
3) wrench 19 mm;
4) end wrench 19 mm with bar;
5) slot head screwdriver;
6) plumb or level;
7) steel shims for turnstile leveling;
8) round file;
9) side-cutting pliers;
10) hammer 500 g;
11) plumb or level.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
11
4.2 Product installation
ATTENTION: CAREFULLY READ THIS SECTION OF THE MANUAL
BEFORE INSTALLING THE PRODUCT
4.2.1 Figure 3 –plan the installation places of fencing panels, turnstile
moving and fixed elements, cable routes in advance according to the detail
drawing.
Figure 3 –Turnstile mounting dimensions

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
12
ATTENTION: NOTE THAT CABLE ENDS MUST PROTRUDE 4
METERS ABOVE THE SOIL LEVEL, SINCE ELECTRICAL CONNECTIONS
ARE MADE IN THE UPPER TURNSTILE MODULE.
4.2.2 The surface intended for the high turnstile installation
must be without irregularities, it must be prepared in advance. We
recommend to use concrete or other non-flammable material for this
purpose.
4.2.3 Mark holes drilling places using the template following
the instructions of the installation drawing.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
13
Figure 4 –Turnstile installation template

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
14
4.2.4 Figure 4 –according to the installation dimensions, prepare 12
holes, 18 mm in diameter, in the floor for anchors of the turnstile stand with a
depth of 80 mm.
Position of mounting holes relative to the overall dimensions of the turnstile
is shown in Appendix B. The depth of holes for embedded parts shall exceed the
anchor length by 5 mm. Insert anchors into the holes.
ATTENTION: DESPITE THE FACT THAT ANCHOR BOLTS OF
THE MANUFACTURING PLANT ARE SUITABLE FOR THE MOST
TASKS, IN EACH SPECIFIC CASE DURING INSTALLATION TAKE
INTO ACCOUNT THE AMBIENT CONDITIONS AND TYPE OF
SOIL ON WHICH THE TURNSTILE IS INSTALLED.
ATTENTION: ALL CONSTRUCTION WORKS MUST BE
AGREED AND APPROVED BY THE QUALIFIED ENGINEER
AWARE OF ALL THE REQUIRED INFORMATION.
ATTENTION: THE EQUIPMENT MUST BE ATTACHED TO THE
FOUNDATION BEFORE OPERATION! THE MANUFACTURING PLANT
SHALL NOT BEAR RESPONSIBILITY FOR ACCIDENTS OR FAILURES
CAUSED BY INCORRECT EQUIPMENT FIXING.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
15
4.2.5 Install the fastening clamps (Appendix C) using the bolts from the
anchor set at the turnstile fastening places (bolts with anchors are not provided).
Tighten the bolts to fix the expanding anchors in soil.
4.2.6 Select the rack of fixed fencing panel on which the turnstile
control and supply cables will be laid to the upper module.
Prepare a cable conduit going from the site to the place of installation, CP
and, where necessary, to the ACS and SFAS connection point.
Cable grooming to the upper module is made via the holes in racks of fixed
fencing panel (Figure 5 –6,7).
Figure 5 –General view of the turnstile

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
16
Prepare cable trench to that rack of fixed module which will be used for
laying of cables to the upper module.
4.2.7 Figure 6 –assemble the turnstile fixed fencing panel. Install it on
the prepared site, previously passing CR cables, power cable, ACS and SFAS
cables via its rack to the upper module.
Figure 6 –Assembly of fixed fencing panel

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
17
4.2.8 Figure 7 –fasten the turnstile fixed fencing panel using the
fastening clamps (1) 2 pcs, М12 anchor bolts (2), screwing them into appropriate
anchors using the 19 mm wrench (two fastening options).
Figure 7 –Fastening of fixed fencing panel
Figure 8 –Fastening of fixed panel (option 2)

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
18
4.2.9 Figure 9 –install and fasten the turnstile fencing fixed elements
using the anchors, screwing them into appropriate holes using the 19 mm wrench.
Install plastic caps on the heads of fastening bolts.
Figure 9 –Installation of fixed fencing elements

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
19
4.2.10 Assemble the moving turnstile elements (rotor gate) as per
figures 9-11.
Figure 10 –Assembly of turnstile rotor gate.

VZR.249600.000IM
Cube C-10 full height rotor turnstile
Installation Manual
20
Figure 11 –Assembly of rotor gate (bottom)