Oxgard Cube C-01 Instruction sheet

Installation
guidelines
www.oxgard.com
[email protected]
Tel.[phone]
Cube С-01 turnstile

Installation guidelines 3
CONTENTS
List of abbreviations used ............................................................................ 4
2. Product Design......................................................................................... 6
3. Safety requirements................................................................................ 11
4. Installation of a turnstile......................................................................... 12
4.1. Required equipment ......................................................................... 12
4.2. Installation of a turnstile................................................................... 13
5. Connecting turnstile ............................................................................... 16
5.1. Power connection ............................................................................. 18
5.2. Connecting Control Panel ................................................................ 19
5.3. Connecting Access Monitoring and Control System
(AMCS)(optionally) ................................................................................ 19
Appendix 1. Brief Description of Data Bus CAN2.0................................ 26
Appendix 2. Location of installation holes with respect to external
dimensions of the turnstile ......................................................................... 27

Cube С-01 turnstile 4
List of abbreviations used
PS –Power Supply
SFAS –Security and Fire Alarm System
ACS –Access Control System
NC –normally connected
NO –normally opened
Firmware version of turnstile FW Cube v 1.2

Installation guidelines 5
1.Basic specifications
Table 1. General Specifications
Specification
Turnstile
Panel
Overall dimensions(H х W х D), mm:
-in operating condition
-with fold down arms
1024х800х900
1024х200х361
107х107х25
Weight, kg
25
0.5
Temperature range, °С:
-operation
-transportation and storage
+1...+40
+1...+40
+1...+40
+1...+40
Relative humidity, %, no more
80
80
Passage width, mm
500
Throughput, person/min
30
Lifetime, years
8
8
Table 1.Electrical characteristics
Specification
Turnstile
Panel
Power supply voltage, V:
-rated
-working
12.0
10.8...13.2
12.0
7.5...15
Standby average current*, А
0.4
Average current in a pass mode*, А
0.4
Maximum absorbed current, А
1.5
*- values indicated at rated voltage
** The manufacturer will reserve the right for changing configuration, technical specifications and
appearance of the product without notice

Cube С-01 turnstile 6
2. Product design
Turnstile housing
Turnstile housing and blocking arms are made of brushed stainless
steel. In the middle part of the housing there is a dismountable bent plate
made of stainless steel for quick access to the cross-board for connection
of cables PS, remote control panel and ACS. At the lower part of the
turnstile housing there is a hole for entry of these cables.
Basement cover shall be fixed with double-sided adhesive tape or
sealing compound. The cover hides turnstile fixation to the floor (Fig.1).

Installation guidelines 7
Fig.1. General View and Overall Dimensions of Turnstile

Cube С-01 turnstile 8
ATTENTION! To log passages during turnstile operation under ACS
control and to avoid unauthorized passages, it is required to arrange
passage zones as per Fig.2.
Ограждение
200 мм min
Не более
50 мм
Планка
ограждения
Recommended installation diagram Not recommended installation diagram
Fig 2. Arrangement of turnstile passage zone
When installing the turnstile it is necessary to consider possible free
movement of the arm, in the STOP mode it constitutes 6 grades in each
direction, Fig 3.
Fence
No more than
50 mm
200 mm
Blocking
arm

Installation guidelines 9
Ограждение
Турникет
9,5
град.
6 град
Fig. 3. Possible free movement of the arm, in “STOP”
mode
Indication panel
Indication panel of the turnstile is located at the upper part of the
turnstile behind the insert made of acryl glass. Operation modes of the
turnstile are displayed on the panel in form of mnemonic signs depicting
authorization and non-authorization of passage (Fig.4).
6 degrees

Cube С-01 turnstile 10
Fig.4.Appearance of indication panel
Control panel
Housing of remote control panel is made of brushed stainless steel.
In the front there are control buttons 1 - 4 and LEDs indicating operation
modes of the panel (Fig.5). Standard cable length, included in the delivery
set, is 5 meters
.
Fig. 4. Appearance of control panel
Sign permitting
passage
Sign prohibiting
passage
Light Emitting Diodes
(LEDs)
Buttons

Installation guidelines 11
3. Safety requirements
ATTENTION! A failure to observe safety requirements, indicated in this
Section, may cause damage to life and health of people, complete or partial
loss of operating capability of the product and (or) auxiliary equipment.
ATTENTION! The manufacturer shall disclaim the liability for causing
injury to human life and health complete or partial loss of operating
capability of the product and (or) auxiliary equipment in case of a failure
to observe safety requirements, indicated in this Section, and will
terminate the validity of the product warranty.
IT IS FORBIDDEN:
to install power supply module inside the body of the turnstile as it
may result in an injury of people due to electric shock;
to install the turnstile outside dry and heated premises;
to use pastes and liquids chemically aggressive to the materials of the
body for cleaning purposes of the product.

Cube С-01 turnstile 12
4. Installation of a turnstile
ATTENTION! The turnstile should be installed securely to avoid
swinging and (or) overthrow during operation. In case of installation on
the low strength floors - take action to strengthen the floor at the
installation site.
Before checking operability of the turnstile carefully read this section of
the Guidelines.
4.1. Equipment required
Equipment used in the process of installation of the turnstile:
electric drill;
hard alloy drill 12 mm in diameter for drilling holes for anchors
in the floor (recommended anchor is the one equipped with the
screw of FH 12/10 SK type);
S5 internal hex wrench for screws;
slotted screwdriver;
plummet or leveling gauge;
steel liners for turnstile aligning;
round file;
side cutters.

Installation guidelines 13
4.2. Installation of turnstile
4.2.1. Prepare horizontal surface at the installation site of the
turnstile.
4.2.2. Prepare cable conduit coming from the site to the installation
area of PS, remote control panel, and as well, if it is required, to the
connection point of ACS and SFAS.
4.2.3. According to the setting dimensions (Fig.6), prepare 3 holes 12
mm in diameter in the floor for fixation anchors of the turnstile housing.
Location of the installation holes related to external dimensions of the
turnstile is presented in the Appendix 3 (Fig.13). Depth of the hole should
exceed the length of the anchor for more than 5mm. Insert the anchors in
the holes.
4.2.4. Cable routing is exercised through the hole 1 (Fig.6) located
at the lower turnstile panel. It is required to prepare the trench for cable
laying. Open the box and unpack:
turnstile housing;
remote control panel with cable;
base cover;
4.2.6. Lay to the wiring duct or trench the connecting cable for
remote control panel, cable for PS and, if provided, ACS and SFAS
cables.

Cube С-01 turnstile 14
Fig. 6. . Installation dimensions (Provided a drawing
of the bottom support of the turnstile)
4.2.7. Mount the turnstile housing to the prepared site (Fig.6). Put
remote control panel, PS and, if necessary, ACS and SFAS cables to the
turnstile housing. Cables feed will be done through the hole 1 located at
the bottom plate of the turnstile (Fig.6). Secure cables with cable ties.
Hole 1 for
control
cable inlet
Cross-section 0-0
4 holes
4 packages
4 radii
4 holes

Installation guidelines 15
Fig.7. Installation diagram of the turnstile
4.2.8. Match the holes in the turnstile support (1, Fig.7) with the
anchors in the floor. Check verticality of the installation in 2 planes, if
necessary use steel gaskets of the required thickness for right
installation of the turnstile. Fix the rack of the turnstile with three
screws М8 (2, Fig 7), having screwed them to the appropriate anchors
using internal hex wrench S5. Fix the base cover with double-sided
adhesive tape.
4.2.9. Remove protective film from the turnstile housing.

Cube С-01 turnstile 16
5. Connecting turnstile:
PS, remote control panel and ACS connection is carried out with a
cross-board. For this it is required to unscrew 2 self-drilling screws located
on the turnstile rack and remove dismountable bent plate made of stainless
steel for quick access to the turnstile cross-board (Fig.8).
Fig.8 shows the cross-board arrangement on the turnstile rack.
Fig. 8. Cross-board arrangement on turnstile rack
Fig.9 shows external view of the cross-board and arrangement of the
connectors for connecting PS, remote control panel, ACS and SFAS.
Unscrew two self-
drilling screws for
plate removal
Cross-board

Installation guidelines 17
Fig.9. External View of the Cross-board
Table 3.Operation modes of a turnstile
Jumper position
Operating mode of the turnstile
J1 removed
Pulse mode (see i.5.3.)
J1 installed
Potential mode (see i.5.3.)
J2 installed
Turnstile does not react to the control panel
instructions, button status translated to the
outputs I/O1...I/O4 (see i.5.4)
J2 removed
Turnstile is controlled by the control panel,
button status translated to the outputs
I/O1...I/O4 (see paragraph 5.4)
-Jumper J3 not used
-Jumper J4 used for arrangement of the normal function of the bus
CAN2.0. see Appendix 1.

Cube С-01 turnstile 18
5.1. Power connection
ATTENTION! It is prohibited to use power units with output current less
than 1.5А.
It is not recommended to install a power unit at a distance more than 25 m
off the turnstile.
ATTENTION! It is prohibited to connect turnstile power with a cable
with cross-section less than 1.5 mm2. When length of the feeding cable is
more than 10 m it is recommended to use cable with dimensions equal to
2.5 mm2.
The turnstile is powered by 12V DC voltage. Мaximum current draw
occurs in “Free passage mode” and constitutes – 1.5А. Power Supply Unit
shall be selected on the basis of these ratings. Also take in consideration
that with increase of the supplied cable length a voltage drop is increased
(operating voltage range is given in Table 2).
Install PS at the place, free for an access of the operator. Connect PS
cable to POWER group of the contacts located on the cross-board. The
contacts (+) and (-) of PS to be connected to the contacts (12V) and (GND)
correspondingly.
Secure connection of the cable. Fit the dismountable bent plate in its
place and fix it with self-tapping screw.

Installation guidelines 19
5.2. Connecting Control Panel
Remote control panel shall be connected to the Control Board group
of contacts located on the cross-board. The contacts will have to be
marked as follows: 12V, CL, CH, GND.
Remote control panel connection shall be made on the basis of
contact marking, provided in Table 4.
Table 4.Contact marking for REMOTE CONTROL PANEL connection
Contact marking
Colour of wire
12V
Red
CL
Yellow
CH
Green
GND
Blue
5.3. Connecting ACS (optionally)
ACS Controller will have to be connected to the group of contacts:
Access Control System located on the cross-board. The contacts will
have to be marked as follows: LEFT, RIGHT, STOP, AP, GND. Contact
assignment is indicated in Table 5.

Cube С-01 turnstile 20
Table 5. ACS contact assignment
Marking of contacts
Contact assignment
LEFT, RIGHT
One-pass movement to the left/to the right
(lowest priority)
STOP
No Entry (“Stop” mode)
(medium priority)
AP
"Antipanic" mode –passage is authorized in
both directions
(highest priority)
GND
Common contact
Inputs for ACS connection will have to be identified by means of
priorities:
AР input possesses the highest priority. At GND contact of this
input the turnstile is in antipanic mode and DOES NOT REACT (!!!) to
the other signals; on the indication panel both arrows “to the left” and
“to the right” are flashing.
Input STOP possesses medium priority. At GND contact of this
input the turnstile changes over to a “Stop” mode and does not react to
the other influences, except for AP;
LEFT and RIGHT possesses equally low priority and include one
pass to one or another side. If both inputs are closed, the pass will be
allowed to the side which input closed first. In case the pass fails to be
done the turnstile will automatically change over to “Stop”mode 5
second later.