Oxgard Cube C-01 Quick start guide

Operational
manual
www.oxgard.com
[email protected]
Тel. [phone]
Cube С-01 turnstile

Operating Instructions 3
CONTENTS
List of Abbreviations used ........................................................................... 4
1. Product Designation................................................................................. 5
2. Standard Equipment (Supplied Package of a Product)............................ 5
3. Main Technical Specifications................................................................. 6
4. Product Design......................................................................................... 7
5. Transportation and Storage .................................................................... 11
6. Safety Requirements .............................................................................. 12
7. Turnstile Operation ................................................................................ 13
7.1. Turnstile Switch On.......................................................................... 13
7.2. Turnstile Operating Modes............................................................... 14
7.3. Adjustment of remote control panel................................................. 20
8. Troubleshooting ..................................................................................... 22

Cube С-01 turnstile 4
List of Abbreviations used
PS –Power Supply
SFAS –Security and Fire Alarm System
ACS –Access Control System

Operational manual 5
1. Product purpose
Cube С-01 turnstile is designed for access control and crowd
management. The turnstile can be used at the guard desks of enterprises
and organizations, in the institutions, banks, educational institutions, sport
and recreational facilities, shops, stations etc.
To ensure a convenient and quick passage of persons it is
recommended to install one turnstile for each 500 persons operating at one
shift.
2. Delivery set
Тable 1. Scope of supply
Denomination
Quantity
Cube С-01 turnstile
1 pc
Remote control panel with a cable
1 pc
Base Cover
1 pc
Product Passport
1 pc
Installation Instructions
1 pc
Technical Maintenance
1 pc
Operating Instructions
1 pc
Anchor with a screw of FH 12/10 SK * type
3 pcs
Connecting cable PVA 2x1.5
1 pc
*- optional

Cube С-01 turnstile 6
3. Basic specifications
Тable 2. Basic Specifications
Specification
Turnstile
Panel
Overall dimensions (H хW хD), mm:
-in operating condition
-with fold down arms
1024х800х900
1024х200х361
107х107х25
Weight, kg
25
0.5
Temperature range, °С:
- in operation
- transportation and storage
+1...+40
+1...+40
+1...+40
+1...+40
Relative humidity, %, no more
80
80
Width of the passage formed, mm
500
Capacity, person/min
30
Lifetime, years
8
8
Table 3. Electrical characteristics
Specification
Turnstile
Panel
Power supply voltage, V:
-rated
-working
12
10.8...13.2
12
7.5...15.0
Standby average current *, А
0.4
Average current in a pass mode **, А
0.4
Maximum absorbed current
1.5
*- values indicated at rated voltage
**The manufacturer reserves the right for changing configuration, technical specifications and
appearance of the product

Operational manual 7
4. Product design
Turnstile housing
Turnstile housing and arms are made of brushed stainless steel. In the
middle part of the body frame there is a dismountable bent plate made of
stainless steel for quick access to the cross-board for connection of cables
PS, remote control panel and ACS. At the lower part of the turnstile rack
there is a hole for entry of these cables
Basement cover shall be fixed with double-sided adhesive tape or
sealing compound. The cover hides turnstile fixation to the floor (Fig.1).
Fig. 1. General view and overall dimensions of turnstile

Cube С-01 turnstile 8
ATTENTION! To log passages during turnstile operation under ACS
control and to avoid unauthorized passages, it is required to arrange
passage zones as per Fig.2
Ограждение
200 мм min
Не более
50 мм
П л а н к а
ограждения
Recommended installation diagram Not recommended installation
diagram
Fig.2. Arrangement of turnstile passage zone
When installing the turnstile it is necessary to take into account possible
free movement of the arm, in the STOP mode it constitutes 6 grades in
each side, Fig 3
Fence
no more than
50 mm
200 mm
Blocking
arm

Operational manual 9
Ограждение
Турникет
9,5
град.
6 град
Fig. 3. Possible free movement of the arm, in “STOP” mode
Indication panel
Indication panel of the turnstile is located at the upper part of the
turnstile behind the insert made of acryl glass. Operation modes of the
turnstile are displayed on the panel in form of pneumonic signs allowing
and prohibiting a passage (Fig. 4).
6 degrees

Cube С-01 turnstile 10
Fig. 4. Appearance of indication panel
Remote Control Panel
Housing of turnstile and arms are made of brushed stainless steel. In
the front there are located control buttons 1 - 4 and LEDs indicating
operation modes on the panel (Fig.5). Standard cable length, included in
the delivery set, is 5 meters.
Sign permitting
pathway
Sign prohibiting
pathway

Operational manual 11
Fig. 5. External view of control panel
5. Transportation and Storage
Turnstile in its original packaging shall be transported by air, by road
and by railroad with protection from direct exposure to rain and dust
without range limitation. For transportation the turnstile is required to be
folded in following i.7.2 of the Instruction7.2. Turnstile Operating Modes
It is allowed to stack boxes in 2 rows during transportation and storage if
Euro-pallets are used. Keep the turnstile in dry (no moisture condensation)
heated places within +1 to + 40 °C temperature range. Avoid vapors of
acids, alkalis, and corrosive gases at the storage place. Storage of turnstile
in the original package in a dry unheated premises or closed transport
containers is permitted for short periods, no more than 3 days. Before
startup, the turnstile must be kept in a room with normal climate
conditions for 12 hours after storage in unheated rooms.

Cube С-01 turnstile 12
Packaging dimensions 270х430х970 mm (H хW хL).
6. Safety Requirements
ATTENTION! A failure to observe safety requirements, indicated in this
Section, may cause damage to life and health of people, complete or partial
loss of operating capability of the product and (or) auxiliary equipment.
ATTENTION! Installation of turnstile shall be carried out by skilled
professionals according to Installation Instruction.
ATTENTION! The manufacturer shall disclaim the liability for causing
injury to human life and health complete or partial loss of operating
capability of the product and (or) auxiliary equipment in case of a failure
to observe safety requirements, indicated in this Section, and will
terminate the validity of the product warranty.

Operational manual 13
IT IS FORBIDDEN:
to install power supply module inside the body of the turnstile as it
may result in an injury of the human beings due to an electric shock;
to install the turnstile outside dry and heated premises;
to use pastes and liquids chemically aggressive to the materials of the
housing for cleaning purposes of the product.
7. Turnstile Operation
7.1. Turnstile Switch On
The turnstile is supplied in a folded state (transportation mode). Before
starting the operation it shall be transferred to the working position:
- unscrew a fixing screw 4 (Fig.9) and elevate the turnstile head up to the
stop.
- screw in a fixing screw 4 (Fig.9) for fasten purpose of a turnstile head
- screw in a screw 3 (Fig.9) for secure fastening of the turnstile head.
- retract a fixation lock 2 of the arms (Fig.6), holding one arm by the hand
in a fixed position, unfold other arms into operating position.

Cube С-01 turnstile 14
Connect PS to the mains ~220V and switch it on. On the indication
panel of the turnstile the red cross will light up, prohibiting the passage,
LED indicator of the button 2 located on REMOTE CONTROL PANEL
(Fig 5) will light red. One of the arms is in state of blocking that prohibits
the passage. The turnstile is ready for operation.
7.2. Turnstile Operating Modes
The turnstile has several modes of operation. The desired mode is set by
using RC panel or ACS. Operational modes displayed on the panel in the
form of mnemonic signs depicting authorization and non-authorization of
passage. Operation by ACS is described in the installation guidelines. This
section describes operation by RC panel. General view of RC panel is
shown in Fig. 3.
The "Stop" mode
"Stop" mode is set when the turnstile is turned on. Switch from another
mode to "Stop" is performed by pressing button 2, in this case LED
indicator above button 2 turns red. In this mode the passage is non-
authorized in both directions. Central arm can be deflected from its initial
position on a small angle. The stopper will be turned on automatically and
will not let the arm to rotate for passage, and then the arm will return to its
original state.
Single passage mode

Operational manual 15
Button 1 (3) turns on single passage mode to the left (right). This mode
allowes one pass to the left (right) with a subsequent changing to "Stop"
mode. Green arrow indicator turns on on the display showing a free
passage to the left (right). Green LED indicator on the RC panel turns on
above the button corresponding to the authorized passage and a red
indicator - above button 2. If the passage is not performed within 5
seconds, the turnstile switches to "Stop" automatically.
Multiple passage in one direction mode
In order to switch to this mode press and hold button 2 and then press
button 1 (3). After that release both buttons. Multiple pass mode is
displayed on the RC panel by green light above the button 1 (3). Red LED
indicator above button 2 is off. Arrow indicator on the LED panel shows
the direction of the authorized passage. In this mode the passage is allowed
in the authorized direction for an unlimited number of times. It is also
possible to authorize a single pass into the non-authorized direction by
pressing button 1 (3). After this passage or within 5 seconds turnstile will
return to the original mode.
Free passage mode
In order to switch to this mode it is required to press and hold button 1,
then press 3 and release both buttons. In this mode passage is allowed in
both directions for an unlimited number of times. Arrow indicators on the
LED panel blink in both directions. Green LED indicators on the RC panel
turn on above the buttons 1 and 3.

Cube С-01 turnstile 16
“Аntipanic”mode
Switching to this mode is carried out by mechanical way. Switch the
turnstile to “Antipanic” mode, to do this press button 4 on the control
panel. Pull off fixation limit stop 2 of the arms (Fig.6), holding one arm by
hand in a fixed position, rotate the other arm clockwise in such a way that
all the arms are aligned (Fig.7). Then tighten further down all the arms
folded together (Fig.8)
While doing so there green arrows will flash indicating both directions on
the indication panel.
Fig.6.

Operational manual 17
Fig 7.

Cube С-01 turnstile 18
Fig. 8.
“Transportation” mode
This mode is used for transportation. To enter this mode, arms shall be
folded as described in “Antipanic”mode. Raise all folded arms to
horizontal position, then fully unscrew the screw 4 (Fig.9) located on
turnstile housing, loose the screw 3 (Fig.9) and move the turnstile head
down so that all folded arms would fit the bent of the turnstile leg
(Fig.10).

Operational manual 19
Fig.9.

Cube С-01 turnstile 20
Fig. 10.
7.3. Adjustment of remote control panel
Turnstile can be set in various directions in relation to the user. In
some cases it is needed to reverse left / right passage buttons. This can be
done by the following operations:
Switch off the power of the turnstile;