Oxgard Cube C-01 User manual

Maintenance
operations
www.oxgard.com
[email protected]
Tel. [phone]
Cube С-01 turnstile

Technical Maintenance 3
CONTENTS
1. General instructions.................................................................................. 4
2. Conditions for performance of technical maintenance............................ 5
3. Partial disassembly of the turnstile .......................................................... 5
4. Checking turnstile assemblies................................................................ 11
5. Lubricating sliding parts of turnstile mechanisms................................. 11
6. Assembly and functionality test of the turnstile .................................... 14

Cube С-01 turnstile 4
1. General instructions
1.1. During operation of the turnstile in order to maintain efficiency and to
ensure calculated lifetime the maintenance operation of the turnstile shall
be carried out periodically, including the warranty period (hereinafter
MO).
1.2. MO shall be performed once in 6 months. Should there be any failure
MO should be performed immediately after repair works.
1.3. During MO it is recommended to carry out the work by two qualified
mechanical and electrical engineers, acquainted with the manual.
1.4. MO includes the following scope of work: partial disassemble of the
turnstile, cleaning of load-bearing frame, checking of parts and units
fixation, lubrication of subject to wear parts of actuating device, checking
of belt tension, setting the dismantled parts and a general inspection of the
turnstile.

Maintenance operations 5
2. Conditions for performance of technical maintenance
ATTENTION! It is strongly forbidden to perform works with connected
power of the turnstile. A failure to observe safety requirements, indicated
in this Section, may cause damage to life and health of people, complete or
partial loss of operating capability of the product and (or) auxiliary
equipment.
ATTENTION! It is strongly forbidden to unfasten a cross-board, located
under the indication panel. Otherwise the manufacturer will terminate the
validity of warranty for the product.
ATTENTION! It is not recommended to adjust stroke limitation units for
solenoids, neither to adjust tension of springs. These units have been
adjusted at the factory. Disturbance of these adjustments may cause
malfunctions for the whole electromechanical system.
3. Partial disassembly of the turnstile
General View of the turnstile is shown on Fig.1
Switch off the power supply unit of the turnstile and disconnect it from the
mains.

Cube С-01 turnstile 6
To get an access to all required units of the turnstile it is necessary to
disassemble the turnstile partially. This scope of works includes removal
of the protective backshell. In order to get that done unscrew two screws
(1) and four screws (2), smoothly move the backshell up at a small
distance so that not to break the cable, coming to the indication board (Fig.
2). Disconnect the cable from the indication board.
Move the backshell up to the end and release an access to the swivel
mechanism. The view after removal of the backshell is shown on Fig 3.
Fig.1
Indication
panel
Rotary mechanism
equipped with
control unit
Protective
backshell
Rack
Base

Maintenance operations 7
Fig.2
Move
up

Cube С-01 turnstile 8
Fig.3
Fold arms for ease of further work, to achieve this retract fixation lock 2 of
the crossbars (Fig.3) and while holding one crossbar in a fixed position
rotate the other crossbar by the other hand clockwise so that all the
crossbars would align (Fig 4), put folded arms down (Fig 5) .

Maintenance operations 9
Fig.4

Cube С-01 turnstile 10
Fig.5

Maintenance operations 11
4. Checking turnstile units
4.1. Clean turnstile parts from contaminants.
4.2. Check if all the cables are properly connected.
4.3. Check and tighten if necessary thread connections that fasten
turnstile units.
5. Lubricating moving parts of turnstile mechanisms
To get an access to the assemblies, for lubrication of the moving parts of
turnstile mechanisms it is required to:
1. Remove lower decorative board having undone two screws 1
(Fig.6)
2. Remove arms unit - to get this:
2.1. Unscrew fixation lock 2 with box spanner D22
2.2. Loose a screw М8, which is in the hole where the fixation lock
was secured with hexagonal key S6.
2.3. Loose two screws 1 (Fig.4) М8 with hexagonal key S6
2.4. Remove arms unit.
Lubricate the details of the turnstile mechanism (Fig.7) indicated with
numbers 1, 2, 3 and 4.
Lubricating is performed by engine oil of viscosity grade 5W-20 at a rate
of 2 - 3 drops in each slide assembly.

Cube С-01 turnstile 12
Fig.6

Maintenance operations 13
Fig.7

Cube С-01 turnstile 14
6. Assembly and functionality test of the turnstile
6.1. In case some faults of its units are detected in the process of
turnstile TM it is recommended to consult the customer care. List of
addresses of the official dealers and service centers is provided in the
Operator’s manual and is available on the web-site: www.oxgard.com
6.2. In case of repair of damaged painted surfaces one should use
powder paint, identical to the damaged (RAL9005), guiding the
instructions for its use.
6.3. Fulfill an assembly of the turnstile in the reverse order.
6.4. Connect the power of the turnstile and carry out functionality
test, having done several test runs.
6.5. If there is neither abnormal noise nor any violations of the
operation modes the turnstile is ready for operation.

Maintenance operations 15

OOO “Vozrozhdenie”
66, Sofiyskaya str.,
192289, Saint-Petersburg
tel./fax [phone]
www.oxgard.com
[email protected]