Oxgard Cube C-02 Instruction sheet

Installation
guidelines
www.oxgard.com
[e-mail]
Tel.[phone]
Cube С-02 turnstile

Installation guidelines 3
CONTENTS
List of abbreviations used ………………………………………………….. 4
1. Basic specifications …………………………………..…………………. 5
2. Product design ………………………………………..………………..... 6
3. Safety requirements ……………………………………………...…. 10
4. Installation of a turnstile …………………………………..………... 11
4.1. Required equipment …………………………………………….……. 11
4.2 Installation of turnstile ……………………………………….…..…. 12
5. Connecting turnstile ………………………………………..…….….…. 15
5.1. Power connection …………………………………………..……..…. 19
5.2. Connecting Control Panel ……………………………………….…… 20
5.3.Connecting ACS (optionally) ……………………………………...… 20
Appendix 1. Summary of data bus CAN2.0 29 ……………...………..… 27
Appendix 2. Location of installation holes related to external dimensions of
the turnstile …………………………………………………………….…. 28
Appendix 3. Diagram of the turnstile and its connection ……………...… 29

Cube С-02 turnstile 4
List of abbreviations used
PS – Power Supply
SFAS – Security and Fire Alarm
RC – Remote Control Panel
System ACS – Access Control System
NC – normally connected
NO – normally opened
Firmware version of turnstile FW Cube v 2.1

Installation guidelines 5
1. Basic specifications
Table 1. General Specifications
Specification
Turnstile
Panel
Overall dimensions(H хW хD), mm:
-in operating condition
-with fold down arms
801х801х780
281х801х780
107х107х25
Weight, kg
15
0.5
Temperature range, °С:
-operation
-transportation and storage
+1...+40
+1...+40
+1...+40
+1...+40
Relative humidity, %, no more
80
80
Passage width, mm
500
Throughput,person/min
30
Lifetime, years
8
8
Table 2.Electrical characteristics
Specification
Turnstile
Panel
Power supply voltage, V:
- rated
- working
12.0
10.8...13.2
12.0
7.5...15
Current type
direct
Standby average current*, А
0.4
Average current in a pass mode*, А
0.4
Maximum absorbed current, А
1.5
*- values indicated at rated voltage
** The manufacturer will reserve the right for changing configuration, technical
specifications and appearance of the product without notice

Cube С-02 turnstile 6
2. Product design
Turnstile housing is made of:
-blocking arms
-wall mount bracket
Blocking arms:
Housing and blocking arms are made of brushed stainless steel.
Wall mount bracket:
Wall mount bracket designated to secure arms block fixation to the
turnstile installation sight. Arms block and bracket are connected with each
other through the bolt.
Fig. 1. General View and Overall Dimensions of Turnstile

Installation guidelines 7
ATTENTION! To log passages during turnstile operation under ACS
control and to avoid unauthorized passages, it is required to arrange passage
zones as per Fig.2.
Recommended installation diagram Not recommended installation diagram
Fig 2. Arrangement of turnstile passage zone
When installing the turnstile it is necessary to consider possible free
movement of the arm, in the STOP mode it constitutes 6 degrees in
each
direction, Fig 3.

Cube С-02 turnstile 8
Fig. 3. Possible free movement of the arm, in “STOP” mode
Indication panel
Indication panel of the turnstile is located at the upper part of
the
turnstile behind the insert made of acryl glass. Operation modes
of the
turnstile are displayed on the panel in form of mnemonic signs
depicting
authorization and non-authorization of passage (Fig.4).

Installation guidelines 9
Fig. 4. Appearance of indication panel
Control panel
Housing of remote control panel is made of brushed stainless steel.
In the front there are control buttons and LEDs indicating operation
modes of the panel (Fig.5). Standard cable length, included in the
delivery
set, is 5 meters

Cube С-02 turnstile 10
Fig. 5. Appearance of control panel
3. Safety requirements
IT IS FORBIDDEN:
•to install the turnstile outside dry and heated premises;
•to use pastes and liquids chemically aggressive to the materials of the
body for cleaning purposes of the product.
ATTENTION! A failure to observe safety requirements, indicated in this
Section, may cause damage to life and health of people, complete or partial
loss of operating capability of the product and (or) auxiliary equipment.
ATTENTION! The manufacturer shall disclaim the liability for causing
injury to human life and health complete or partial loss of operating
capability of the product and (or) auxiliary equipment in case of a failure
to observe safety requirements, indicated in this Section, and will
terminate the validity of the product warranty.
Light Emitting Diodes
(LEDs)
Buttons

Installation guidelines 11
4. Installation of a turnstile
4.1 Equipmentrequired
Equipment used in the process of installation of the turnstile:
•electric drill;
•hard alloy drill 10 mm in diameter for drilling holes for anchors
in the wall (recommended anchor MSA8 with the screw of
DIN7991 M8x25);
•S5 internal hex wrench for screws;
•slotted screwdriver;
•plummet or leveling gauge;
•steel liners for turnstile aligning;
•side cutters.
ATTENTION! The turnstile should be installed securely to avoid
swinging and (or) overthrow during operation. In case of installation on
the low strength floors - take action to strengthen the floor at the
installation site.
Before checking operability of the turnstile carefully read this section of
the Guidelines.

Cube С-02 turnstile 12
4.2 Installation of turnstile
Diagram of the turnstile and its connection is shown in the Appendix 3
4.2.1 Prepare surface at the installation site of the
turnstile.
4.2.2 Open and unpack the box:
•Blocking arms unit
•Wall mount bracket
•PS with a cable
4.2.3 Prepare cable conduit coming from the site to the installation
area of PS, remote control panel, and as well, if it is required, to
the
connection point of ACS and SFAS.
4.2.4 According to the setting dimensions (Fig.6), prepare 4 holes 10
mm in diameter in the wall for fixation anchors of the turnstile bracket
(recommended anchor MSA8 with the
screw of DIN7991 M8x25).
Depth of the hole 35 mm should exceed the length of the anchor for
more than 5mm. Insert the anchors in
the holes and fix support for
mount bracket with the screws М8х25 to the wall. With 4 screws fix
decorative lid to the turnstile mount support as on the Fig.7. Fix the
blocking arms unit to the mount support with the fastening sleeve
and sleeve fixation screw.
Location of the installation holes related to external dimensions of
the
turnstile is presented in the Appendix 3 (Fig.16).
4.2.5 PS and RC and, if provided, ACS and SFAS cable routing to
the blocking arms unit is exercised through the hole located
at the
back turnstile side.

Installation guidelines 13
Fig. 6. Installation dimensions
(Provided a drawing
of the wall fixation support of the turnstile)

Cube С-02 turnstile 14
Fig.7. Installation diagram of the turnstile bracket support
4.2.6 Remove protective film from the turnstile housing.

Installation guidelines 15
5. Connecting turnstile
Connecting BP, PU, and access control is carried out with the help of
a cross-board located in the block in barrier arms’ unit, under the removable
cover (Fig. 8).
For this it is required to undo 2 screws (1) and 4 screws (2), smoothly
move the cover up on a short distance, without breaking the cable,
connecting the display panel (Fig. 9). Disconnect the cable from the display
board.
Slide the cover to the end and make free the access to a rotary
mechanism. Fig. 10 shows the picture after removing of the cover
Fig. 8. Cross-board arrangement

Cube С-02 turnstile 16
Fig. 9.
To control connections to the cross board, a lid can be removed. For this,
undo 2 M3 screws located on the lid and remove it by pressing your finger
into the unit.

Installation guidelines 17
Fig. 10.
Fig.11 shows the cross-board arrangement and connectors for
connecting BP, CP, ACS and OPS.

Cube С-02 turnstile 18
Fig.11. External View of the Cross-board
Table 3. Operation modes of a turnstile
Jumperposition
Operating mode of the turnstile
Potential
Mode
X1 Position «On»
Potential mode (see i.5.3.)
X1 Position «OFF»
Pulse mode (see i.5.3.)
Remote
Control
X3 Position «On»
Turnstile does not react to the control
panel instructions, button status
translated to the outputs OUT1...OUT3
(see i.5.4)
X3 Position «OFF»
Turnstile is controlled by the control
panel, button status translated to the
outputs OUT1...OUT3 (see paragraph
5.4)

Installation guidelines 19
5.1. Power connection
The turnstile is powered by 12V DC voltage. Мaximum current
draw
occurs in “Free passage mode” and constitutes – 1.5А. Power
Supply Unit
shall be selected on the basis of these ratings. Also take
in consideration
that with increase of the supplied cable length a
voltage drop is increased
(operating voltage range is given in Table 2).
Install PS at the place, free for an access of the operator. Connect
PS
cable to POWER group of the contacts +12U_IN and GND_IN
located on the cross-board. The
contacts (+) and (-) of PS to be
connected to the contacts (12V_IN) and (GND_IN)
correspondingly.
ATTENTION! It is prohibited to use power units with output current less
than 1.5А.
It is not recommended to install a power unit at a distance more than 25 m
off the turnstile.
ATTENTION! It is prohibited to connect turnstile power with a cable
with cross-section less than 1.5 mm2. When length of the feeding cable is
more than 10 m it is recommended to use cable with dimensions equal to
2.5 mm2.

Cube С-02 turnstile 20
5.2. Connecting Control Panel
Remote control panel shall be connected to the Pult group
of
contacts located on the cross-board. The contacts will have to be
marked
as follows: 12V, CL, CH, GND.
Remote control panel connection shall be made on the basis of
contact marking, provided in Table 4.
Table 4.Contact marking for REMOTE CONTROL PANEL connection
Contactmarking
Colour of wire
12V
Red
CL
Yellow
CH
Green
GND
Blue
5.3.Connecting ACS (optionally)
ACS Controller will have to be connected to the group of contacts:
Control located on the cross-board. The contacts will have to be
marked as follows: LEFT, RIGHT, STOP, AP, GND. Contact assignment
is indicated in Table 5.
Table 5. ACS contact assignment
Marking of contacts
Contactassignment
LEFT, RIGHT
One-pass movement to the left/to the right
(lowestpriority)
STOP
No Entry (“Stop” mode)
(mediumpriority)
GND
Common contact