Oxgard Praktika T-01 User manual

MAINTENANCE
OPERATIONS
www.oxgard.com
[email protected]
Tel.[phone]
Praktika T-01 turnstile

Maintenance operations 3
Contents
1. General information ................................................................................. 4
2. Conditions for maintenance ..................................................................... 5
4. Checking turnstile parts.......................................................................... 13
5. Lubrication of moving parts................................................................... 14
6. Assembling and operation checking of the turnstile.............................. 17

Praktika T-01 turnstile 4
1. General information
1.1. During operation of the turnstile in order to maintain efficiency and to
ensure calculated lifetime the maintenance operation of the turnstile shall
be carried out periodically, including the warranty period (hereinafter
MO).
1.2. MO shall be performed once in 6 months. Should there be any failure
MO should be performed immediately after repair works.
1.3. During MO it is recommended to carry out the work by two qualified
mechanical and electrical engineers, acquainted with the manual.
1.4. MO includes the following scope of work: partial disassemble of the
turnstile, cleaning of load-bearing frame, checking of parts and units
fixation, lubrication of subject to wear parts of actuating device, checking
of belt tension, setting the dismantled parts and a general inspection of the
turnstile.

Maintenance operations 5
2. Conditions for maintenance
CAUTION! It is strictly forbidden to carry out work with powered
turnstile. Failure to follow these safety requirements could result in
damage to human life and health, total or partial loss of product
workability and (or) auxiliary equipment.
CAUTION! Do not remove motherboard located under the LED panel.
Otherwise the manufacturer will void the product warranty.
CAUTION! It is not recommended to adjust the limitation units of
solenoid stroke, Hall sensor bracket and spring tension. These components
are adjusted at the factory. Violation of these adjustments may lead to
failures of the whole electromechanical system.
3. Partial disassemble of the turnstile
In order to get access to all elements of the turnstile it is necessary to
perform a partial disassembly. Scope of work includes the dismantling of
the LED panel, the hatch with a lock and the lower panel (Fig. 1).

Praktika T-01 turnstile 6
Fig. 1
3.1. Turn off turnstile power supply and disconnect it from the
electrical network.
3.2. Removing LED panel
•Remove the plastic cover plug from the hole (Fig. 2);
•remove the screw fixing the LED panel using crosshead
screwdriver (Fig. 3);
•slide the LED panel to the direction indicated in Fig. 4, and lift
it up;
•Disconnect the cable from the LED panel.

Maintenance operations 7
Fig. 2

Praktika T-01 turnstile 8
Fig. 3
Fig. 4
3.3. Unlock the hatch and remove it (Fig. 5).
3.4. Next step is to fold the arms. In order to do it press gently on the
arms fixing cam in the direction shown in Fig. 6. Arm shall be free rotating
freely about the short axis. Fold the second arm in the same manner by
turning the disc. The result is shown in Fig. 7.

Maintenance operations 9
Fig. 5

Praktika T-01 turnstile 10
Fig. 6
Fig. 7

Maintenance operations 11
Fig. 8
Fig. 9

Praktika T-01 turnstile 12
3.5. Removing of the lower cover of turnstile:
•Remove two M6 DIN7985 screws (Fig. 8);
•Remove M6 GOST11738-84 screw (Fig. 9);
•Remove the lower cover by moving it vertically down, as
shown in Fig. 10
Fig. 10

Maintenance operations 13
4. Checking turnstile parts
4.1. Clean the load-bearing frame from contamination.
4.2. Check that all cables are securely connected.
4.3. If necessary check and tighten the screw joints of turnstile:
4.4. Check the condition of the toothed belt and its tension (Fig. 11).
4.5. Check the general condition of the rubber plate of stopper unit
(Fig. 11).
Fig. 11

Praktika T-01 turnstile 14
5. Lubrication of moving parts
Lubrication is made with 2 - 3 drops of engine oil (viscosity grade 5W-20).
5.1. The rotation axis of the stopper unit (Fig. 12).
5.2. The rotation axis of the roller lever (Fig. 13).
5.3. Clip between the stopper unit and the solenoid (Fig. 14).
Elements of the unit are located behind the roller lever shown on Fig. 13
5.4. The rotation axis of unlocking arms cam (Fig. 15).
5.5. The connection of lock pin and arms-unblocking cams (Fig. 16). The
operation shall be done for each arm by rotating the disc. Hole in Fig. 16 is
shown in the conventional manner.
Fig. 12

Maintenance operations 15
Fig.13
Fig.14

Praktika T-01 turnstile 16
Fig.15
Fig.16

Maintenance operations 17
6. Assembling and operation checking of the turnstile
6.1. If any troubles or defects are found out during MO it is advised
to contact our service department for advice, contact details are available
online:
www.oxgard.com
6.2. If it is necessary to repair damaged painted surfaces, powder
paint identical to the damaged (RAL9005) shall be used in accordance
with instructions for its use.
6.3. Reassemble the turnstile in reverse order.
6.4. Turn on the turnstile and perform functionality check by making
several passes and activating “antipanic” mode.
6.5. If there is no extraneous noise or any abnormality in the turnstile
work it is ready for operation.

Praktika T-01 turnstile 18

Maintenance operations 19

OOO "Vozrozdenie"
192289 Saint Petersburg
Sofiyskaya st., 66
Tel./fax [phone]
www.oxgard.com
[email protected]