PIR Specification
78963, 78965, 78967 and 78969 are fitted with
PIR motion sensor. The specification is as follows:
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
Technical data
Please read these instructions carefully before commencing
any work.
This light fitting should be connected to a circuit with a
30mA RCD fitted.
The external flexible cable or cord of this luminaire cannot
be replaced; if the cord is damaged, the luminaire must be
destroyed.
This product is not suitable for location in or near a marine
environment.
The entire unit gets hot whilst on for a period of time.
This product is supplied with 1 metres of H05RN-F outdoor
grade rubber sheathed cable - ready for connection to an
approved, outdoor rated terminal block which is not
supplied and must be obtained.
This is a floodlight product, and therefore should be
positioned where it will not cause a glare hazard.
Terminal block not included. Installation may require advice
from a qualified person.
This unit must be fitted by a competent and qualified
electrician.
Check the pack and make sure you have all of the parts listed.
To prevent electrocution switch off at mains supply before
installing or maintaining this fitting.
Ensure other persons cannot restore the electrical supply
without your knowledge.
Install in accordance with IEE Wiring regulations and current
Building Regulations.
Supply
Voltage:
Bulb
Type:
220-240V~, 50 Hz
78963 : 10W LED (SMD), 4000K
78965 : 20W LED (SMD), 4000K
78967 : 30W LED (SMD), 4000K
78969 : 50W LED (SMD), 4000K
The light source of this luminaire is not
replaceable; when the light source reaches its
end of life the whole luminaire shall be replaced.
Conformity with all relevant EC Directive
requirements.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist.Check with your
Local Authority or local store for recycling advice.
This product is not suitable for dimming.
Layout
• The optimum height is between 1m-3m.
Lights can install on the ground and wall or brackets according to actual situation such as installation on the brackets with
hexagonal head screw fixed. And dig the hole on ground or wall with suitable expansion bolt (not provide) fixing according
to light's bracket if install on the ground or wall.
• Cables must be protected using suitable conduit or plastic trunking.
• The mains supply cable must have a minimum cross section area of 1.0mm2.
• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the
junction box and the light fitting.
• Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
If replacing an existing fitting, make a careful note of the
connections.
Class I product, must be connected to earth.
Installation
•Drill and plug the wall at the marked positions.
•Fix the bracket to the wall using the screws and plugs (not provided). Take care to avoid damaging any
concealed wiring and pipes. The correct fixings should be used for brick or cavity walls.
• Hold the product in position and mark the location of the fixing holes. A minimum of two fixing points must be used.
Ensure the wall is capable of holding the weight of the product. The bracket can be removed from the fitting for
ease of installation.
•Wire as detailed wiring.
•Using the allen key (not supplied), loosen the bolts on the side, and adjust the fitting to the desired position.
Ensure that the cable is not snagged. Re-tighten the bolts.
IP
44
Conformity with all relevant UKCA Directive
requirements.
This product is rated at IP44.
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note that the power needs to be isolated/switched off at the fuse board.
Power Source: 220-240VAC
Power Frequency: 50/60Hz
Rated Load: MAX. 50W
Detection Range: 120º
Detection Distance: 8±2m (<24ºC)(adjustable)
Time Setting: 10±5sec-8±2min. (adjustable)
Ambient Light: 2-2000Lux. (adjustable)
Detection Motion Speed: 0.6-1.5m/s
Working TemperaturePower: -10ºC--+45ºC
Working Humidity: <40%RH
Installation Height: 1-3m
induction area figure:
4m±2m
8m±2m
120º
