Mutsy IGO User manual

IGO
instruction manual

18
16
14
5
4
7
13
11
12
10
1
2
17
3
15
5
6
8
12
19
9

e
f
g
d
b
a
c

h
i
m
l
n
j
k o

4
5
5
6
6
3
3
p
q
r
s1
s2
t

5
click!
u1
v1
v1
x1
x2
y
w

EN Instruction manual Mutsy Igo
FR Mode d`emploi Mutsy Igo
ES Manual de instrucciones Mutsy Igo
EN
FR
ES

2
Content
Introduction........................................................................................................... 2
Warnings................................................................................................................ 2
Guarantee.............................................................................................................. 4
Maintenance and points for attention.................................................................... 5
Content of the box.................................................................................................. 6
Summery of parts: corresponding to the summery diagram.................................. 6
Orientation ............................................................................................................ 6
The frame............................................................................................................... 6
The wheels............................................................................................................. 7
The brake ............................................................................................................... 8
The push bar .......................................................................................................... 8
The pram body....................................................................................................... 8
The seat.................................................................................................................. 9
The Maxi-Cosi car seat.......................................................................................... 12
Introduction
·In order to make optimal use of this product we recommend you use it
properly and maintain it well. Read these instructions for use carefully
before you start using the pushchair and keep the instructions for future
reference.
·Should you have any questions, comments or complaints please contact
your retailer.
·If you want to know what accessories are available for this product or if you
want to stay informed of new Mutsy products then go to www.mutsy.com.
⚠WARNINGS
general
·WARNING: Read through these instructions for use carefully, and keep them in a
safe place for future reference. Failure to observe the instructions for use may put
your child’s safety at serious risk.
·WARNING: You are responsible for your own child’s safety. Never leave your child
unattended.
·WARNING: Avoid serious injury fromfallingorsliding out.Always usethe vepoint
safety harness.
·WARNING: Ensure that the frame and handlebar are completely unfolded and that
all locking devices are engaged before use.
·WARNING: Check that the pram body or seat unit or car seat attachment devices
are correctly engaged before use.
·WARNING: Do not let your child play with this product.
·WARNING: Never leave your child unattended, this can be dangerous.

3
EN
·WARNING: Always check that the accessories have been secured properly before
you start using the pram.
·WARNING: Only use the pram for one child at a time.
·WARNING: Always apply the brakes when parking the pram.
·WARNING: Make sure that the brakes are applied when placing or removing
your child.
·WARNING: You must take your child from the pram before lifting the pram or using
stairs, escalators or lifts.
·WARNING: This product is not suitable for running or skating.
·WARNING: Use only replacement parts supplied or recommended by Mutsy.
safety during adjustment
·WARNING: To avoid pinching of ngers, keep children away from the frame when
folding and unfolding the product.
·WARNING: When making adjustments ensure that all parts of the child’s body are
clear of any moving parts
seat
·WARNING: The seat unit is suitable for children from birth up to 55 lbs. (25 kg) and
up to 42.7 in. (108 cm) in height.
·Warning: Child may slip into leg openings and strangle. Never use in fully reclined
position of the seat unless the child is properly secured with the 5-point safety
harness.
·WARNING: Always secure your child with the 5-point safety harness combined
with the strap running between the legs.
·WARNING: After unfolding the seat, always push the bumper bar to its upright
position before placing a child in the seat. Make sure that no child is near the
bumper bar when moving it.
·WARNING: If your child is younger than 6 months always use the pram body or the
fully reclined position of the seat.
pram body
·WARNING: The pram body is suitable for children from birth up to 33 lbs. (15 kg)
and up to 30 in. (76 cm) in height
·WARNING: The pram body is not suitable for children who can sit or turn indepen-
dently or who can raise themselves on their hands and knees.
·WARNING: The pram body can only be used on the frame and not as a standalone cot.
Neverleaveyourchild unattended.
·WARNING: The pram body has a number of bags. The maximum permissible
weight in each bag is 2 Lbs. (1 kg)
·WARNING: Do not use the pram body with a mattress thicker than 25 mm / 0,984
inch. Do not add an additional mattress.

4
stability
·WARNING: A shopping basket is located between the wheels underneath the
frame.The maximum permissible weight for this basket is 22 lbs. (10 kg).
·WARNING: Bags, accessories or both, other than recommended by the manufac-
turer, can, when placed on the product, result in an unstable pram. Exclusively use
original Mutsy accessories.
·WARNING: Overloading can result in a dangerous, instable situation.
·WARNING: Shopping bags or other heavy objects must not be hung on the push
bar due to the risk of toppling.
·WARNING: This product may become unstable if a parcel bag or parcel rack, other
than one recommended by the manufacturer is used.
·WARNING: You need to tilt the pram on its rear wheels if you want to get on or get
o the kerb.
car seat
·WARNING: The maximum permissible weight as indicated on the relevant product
applies when using a car seat.
·WARNING: For car seats used in conjunction with the frame, this vehicle does not
replace a cot or a bed. Should your child need to sleep, then it should be placed in
a suitable pram body, cot or bed.
·The Mutsy Igo has been approved according to the ASTM F833-13b and SOR/2016-
167 standards.
Guarantee
All Mutsy products come with a guarantee period of two years, starting
on the day of purchase. If you encounter a production defect, Mutsy will
work with the retailers to provide a solution. Production defects will be
repaired under guarantee. The guarantee does not apply to exchang-
ing or returning Mutsy products. The guarantee will only be honoured
if you can provide the following at the store at which the product was
purchased:
·a completed guarantee card
·a copy of the purchase receipt
·a clear description of the defect
·your product
The guarantee card can be found on:
www.mutsy.com/usen/service/warranty
This card must be completed correctly and submitted digitally. You will
also need to enter the serial number. This number can be found on a
white sticker on the product; it is usually located on the underside.

5
EN
The guarantee does not apply:
·if the problem concerns fabric discolouration
·if the fabric has been damaged by water
·in relation to damage caused by the use of non-original Mutsy accessories.
·if you cannot provide the purchase receipt
·if you have used the product incorrectly or unreasonably
·in relation to regular wear and tear that occurs as a result of day-to-day use
·in the event of damage caused by bad maintenance, neglect or an accident
·if damage has been caused as a result of modications to the product
that have been carried out by the consumer, without permission from
the manufacturer
·if the damage is not reported promptly (within 2 months)
Mutsy provides no guarantee in relation to shrinkage or defects concern-
ing the fabric elements that have been caused as a result of cleaning.
Safety is a priority for Mutsy. We therefore full the highest safety standards:
·Europe: EN 1888
·UK: BS EN 1888
·Canada: SOR/ 85 - 379
·USA: ASTM F833
For questions or comments, please contact us via: www.mutsy.com/contact
Maintenance and points for attention
The frame
·Regularly check the locking mechanism of the frame. After cleaning
you can spray some Teon spray on it and rub it with a soft cloth. This
also applies to other moving parts.
The wheels
·To let the wheels run more smoothly the wheel axles must regularly be
cleaned and lubricated with acid-free vaseline. The wheels can never
be lubricated with oil.
The fabrics
·Removable fabric parts can be hand-washed with a delicate detergent
(not warmer than 30°C). Do not use the washing machine or tumble
dryer for the cleaning.
·All Mutsy fabrics have been tested on water resistance however if the
pram gets really wet, the water can penetrate the inner and outer fab-
rics and leave circles. To prevent this we recommend you always use the
rain covers in wet weather.

6
·You can treat stains on the outer fabric or lining with some liquid
bleach-free soap. Always treat the whole area.
·Always let a wet pram dry with a fully unfolded hood.
·Even though Mutsy fabrics are selected with the utmost care and are
tested on colour fastness, the fabrics can discolour. Mutsy shall not be
liable for any possible discolouration.
Content of the box
·1 frame with basket
·2 front wheels
·2 rear wheels
·1 seat
Summary of parts
Corresponding to the summary diagram
01. push bar
02. push bar adjustment
03. built-in safeguard
04. frame unlocking buttons
05. attachment point
06. unlocking button for seat, pram body and adapters
07. folding safeguard
08. brake pedal
09. rear wheel
10. front wheel
11. swivelling wheel locking
12. wheel unlocking button
13. foot rest
14. leg support
15. leg support adjustment
16. bumper bar
17. 5-point safety harness
18. hood
19. carry handle
Orientation
·References in the text to the front, rear, left or right side of the pram are
described from the perspective of a user walking behind the pram.
The frame
Unfold the frame (a, b)
·Press the folding safeguard inwards (a1) and tilt the upper frame until

7
EN
the lower support clicks into place (a2) and move the push bar back-
wards until you hear a second click (b).
·If you unfold the frame, with the pushchair seat tted to the frame, you
then have to manually raise the front brace afterwards.
·Before use always check that the pram has been unfolded and secured cor-
rectly.
Fold the frame (c,d)
·Stand behind the frame and put the frame on the brake. Push the
height adjustment button (c1) of the pushbar in and move this to the
lowest setting. Pull the folding safeguard (c2) towards you on both
sides and turn the pushbar forwards until the pushbar lies on the
frame (c3).
·Pinch the frame unlocking buttons and fold the frame (d).
·The folding safeguard locks automatically when the product is folded up.
·The integrated carry handle, which is located under the rear axle, has
made lifting and carrying the folded pushchair more practical.
The wheels
Assemble the rear wheels (e)
·Slide the axle of the rear wheel in the rear wheel casing until you hear a
click. Pull the wheel to check that it has been attached rmly.
Disassemble the rear wheels (f)
·Press the button on the inside of the rear wheel casing and take the
wheel o the frame
Assemble the front wheels (g)
·Slide the axle of the front wheel upwards in the front wheel casing
until you hear a click. Pull the wheel to check that it has been attached
rmly.
Disassemble the front wheels (g)
·Push the button on the front side of the front wheel and pull the wheel
from the front wheel casing.
The swivelling wheels (h)
·Turn the ring above the front wheel inwards on both sides in order to
block the swivel setting. The swivelling wheels will automatically be
locked when the wheels are placed in the rear direction.
·Turn the ring above the front wheel on both sides outwards to unlock
the swivelling wheels.

8
Pumping up the air tires (IGO accessory: rear wheels air tyre set)
·The air pressure in the air tires may decrease after a while. Check the
pressure regularly and is necessary pump up the tires.
·Press the pump rmly onto the valve. Pump up the tires until the re-
quired air pressure has been reached. The air pressure in the tires may
never exceed 16 PSI / 1.1 bars.
·Air tires may leave traces on some surfaces.
The brake (i)
·Push the pedal downwards with your foot to block the brake.
·Push the pedal upwards with your foot to unblock the brake.
The push bar (j)
·The push bar has three dierent height positions. Press the push bar set-
ting button and move the push bar higher or lower while keeping the but-
ton depressed.
·Release the button when the push bar is in the desired position.
The pram body (up to 33 lbs. / 15 kg)
·The pram body is suitable for transporting children from birth up to 33
lbs. (15 kg) and 30 inch (76 cm) in height, in a lying position.
·The pram body is not suitable for children who can sit or roll indepen-
dently or who can raise themselves on their hands and knees.
·This pram body can only be used on the frame and not as a standalone cot.
·Regularly check the bottom and the borders of the pram body on wear
and tear.
·Make sure that the frame has fully been unfolded and the brake blocked
during all actions indicated below.
Place the pram body (k)
·Place the attachable elements on the pram body into the attachment
points on the frame and press the pram body downwards until you
hear a click on both sides.
·Check to ensure that the red sections on the frame attachment points
are no longer visible. Check that the pram body has been installed se-
curely by trying to lift it from the frame.
Remove the pram body (l)
·Slide the unlocking buttons upwards until you hear a click on both sides.
Be careful! The pram body is now unlocked; the red sections on the frame
attachment points are now visible. Take the pram body rmly by the han-
dle on the hood and remove it from the frame in a vertical movement.

9
EN
The hood (m)
·The hood can be unfolded by moving it upwards.
·Push and hold the buttons on the sides of the hood. The hood can now
be folded downwards.
Assemble the rain cover on the pram body (n)
·Make sure that the hood of the pram body has been unfolded.
·Place the rain cover from top to bottom over the pram body and make
sure that the rain cover attaches well all around the bottom of the pram
body.
·Close the Velcro strips around both sides of the frame.
·Open the zipper in order to remove your baby from the pram body
when using the rain cover.
The seat
·The seat unit is suitable for children from birth up to 55 lbs. (25 kg).
! If your child is younger than 6 months always use the pram body or the
fully reclined position of the seat.
·When in the drive position, the seat can be folded and unfolded with
the frame and does not therefore need to be removed from the frame.
·The back support and leg support are adjustable.
·Make sure that the frame has been fully unfolded and the brake is
blocked during all actions indicated below.
Moving the seat unit to face forwards (o)
·Place the attachable elements on the seat into the attachment points
on the frame and press the seat downwards until you hear a click on
both sides. NB! Place both ridges on the attachment elements into
the frame attachment points at the same time.
·Check that the chair has been attached solidly by trying to lift it from
the frame.
Moving the seat unit to face backwards (p)
·In order to place the seat unit so that it is facing backwards, the attach-
ment elements on the seat need to be turned by 90 degrees. Press the
button (p1), the attachment elements will unlock and spring out. Turn
the attachment elements to the correct setting and then click into
place.
·Then place the attachable elements on the seat into the attachment
points on the frame and press the seat downwards until you hear a click
on both sides. NB! Place both ridges on the attachment elements into
the frame attachment points at the same time.

10
·Check that the chair has been attached properly by trying to lift it from
the frame. NB! The frame cannot be folded with the seat facing back-
wards!
Remove the seat (q)
·Slide the unlocking buttons upwards until you hear a click on both
sides. Be careful! The seat is now unlocked; the red section on the frame
attachment points are now visible. The seat can vertically be removed
from the attachment points.
Adjust the back support (r)
·Pull the button at the back of the seat upwards and hold it upwards.
·The back support has 4 positions. Place the back support in the desired
position and release the button to lock the position.
Attach and remove bumper bar (s1)
·To secure the front bumper, press the ends of the bumper into the re-
cesses intended for this purpose on the seat until you hear a click.
·Press the unlock buttons on both sides of the front of the bumper bar
to remove the bumper bar from the chair.
Adjust the leg support (s2)
·Lift the leg support to place it upwards.
·Push the buttons on both sides of the leg support and push the leg
support downwards to lower it.
Fully reclined position (t)
·The seat has a fully reclined position to make the seat suitable for children
from birth ! The use of a suitable pram body is always recommended and
preferred for children from birth up to the age that your child can sit up
unassisted.
·To put the seat in the fully reclined position, put the leg rest in its high-
est position (t1) and the backrest of the seat in its most reclined posi-
tion (t2).
·Release the two press studs on each side of the seat (t3). Open the zip-
per around the leg support (t4). There is a fabric side support in the
pocket behind the leg support, which you can pull out. Now you can
put the side support up and attach the two press studs on each side
onto the plastic shell of the seat (t5). The press studs of the seat cover
can now be attached to the press studs of the side support.
! The hood of the seat needs to be in the rst upright position (not exten-
ded). There are 2 straps on either side of the seat to keep the canopy

11
EN
in this position. Make sure the two straps on either side of the seat are
attached to the press studs on the canopy (t6).
Folding the frame with the seat facing forwards (u)
·Stand behind the chassis and put the chassis on the brake. Fold the
hood back if it is folded out. Fold the seat unit in two by tilting the back
support forwards (s1).
·Push the height adjustment button (s2) of the pushbar in and move
this to the lowest setting. Pull the folding safeguard (s3) towards you
on both sides and turn the pushbar forwards until the pushbar lies on
the frame (s4).
·Pinch the chassis unlocking buttons and fold the chassis (s5).
·The folding safeguard locks automatically when the product is folded up.
·The integrated carry handle, which is located under the rear axle, has
made lifting and carrying the folded pushchair more practical.
·NB! The chassis cannot be folded with the seat facing backwards!
Unfolding the frame with the seat
·Press the folding safeguard inwards (a1) and tilt the upper frame until
the lower support clicks into place (a2) and move the push bar back-
wards until you hear a second click (b).
·After unfolding the seat, always push the bumper bar to its upright po-
sition before placing a child in the seat. Make sure that no child is near
the bumper bar when moving it.
·Before use always check that the pram has been unfolded and secured cor-
rectly.
The hood (v1, v2)
·Hold the front hood bar in the centre and move it forwards or rear-
wards to adjust the hood (v1)
·Open the zipper at the back of the opened hood in order to enlarge it.
Close the zipper to again reduce the hood (v2)
·Pull the ap on the front side of the hood outwards to additionally en-
large the hood. Push the ap inwards to again reduce the hood.
Assemble the rain cover on the pushchair (w)
·Make sure that the hood of the seat is in the upright position.
·Open the zipper in the rain cover in order to attach it to the enlarged
hood of the seat.
·Place the rain cover from top to bottom over the pushchair and make sure
that the rain cover is attached well behind the back support and over the
leg support.

12
The 5-point safety harness (x1, x2)
·Place your child in the pushchair and make sure that the legs of your
child are placed on each side of the leg piece.
·Make sure that the hip and shoulder belt is positioned correctly over
your child and place both plastic clamps in the central part of the har-
ness attached to the leg piece (x1).
·To adjust the length of the shoulder straps, loosen the shoulder protec-
tors from the belt by undoing the velcro. This will reveal the belt buck-
les. Adjust the length by sliding the buckles along both shoulder straps
until your child is comfortably secure. After adjusting, press down the
velcro on both sides to relock the shoulder protectors in place.
·The back support contains three positions for the shoulder belts. To ad-
just the position, open the panel behind the back support (x2). Loosen
the shoulder belts by moving the attachment rings through the open-
ings. Move the attachment rings through the desired openings so that
the shoulder belts are positioned properly and click the panel back.
·Regularly check the length and position of the belts and adjust, where
necessary.
Maxi-Cosi car seat
·The Maxi-Cosi car seat adapters are suitable for use with the Maxi Cosi
Mico: 5-22 lbs. 19-22 in. (2,2-10 kg, 48-74 cm) and Maxi Cosi Prezi: 4-30 lbs.
<29 in. (1.8-13.6 kg, <74cm).
·Always observe the instructions in the manual of your Maxi-Cosi car
seat before you start using the car seat.
·Make sure that the frame has fully been unfolded and the brake blocked
during all actions indicated below.
Place the Maxi-Cosi adapters on the frame (y)
·The adapter marked with ‘R’ is placed on the right side of the frame, the
adapter marked‘L’ is placed on the left side.
·Slide the adapters in the attachment parts and press solidly until you
hear a click.
Place the Maxi-Cosi car seat on the adapters
·Orientate the Maxi-Cosi car seat such that it is directed rearwards on the
frame.
·Hold the Maxi-Cosi car seat with the central hinge points of the support
bar directly above the adapters.
·Lower the Maxi-Cosi car seat and press solidly into the adapters un-
til you hear a click.
·Check that the Maxi-Cosi car seat has been placed horizontally and has

13
EN
been attached properly by trying to lift it from the frame.
Remove the Maxi-Cosi car seat from the adapters
·Operate the unlocking system of the Maxi-Cosi car seat. Lift the Maxi-
Cosi car seat straight up from the frame.
Remove the Maxi-Cosi adapters from the frame
·Slide the unlocking button on the frame attachment points upwards
until you hear a click. The adapter can now be taken o the frame.

14
Table des matières
Introduction......................................................................................................... 14
Avertissements .................................................................................................... 14
Garantie............................................................................................................... 16
Entretien et points importants............................................................................. 17
Contenu du carton ............................................................................................... 18
Liste des pièces vue éclatée.................................................................................. 18
Orientation........................................................................................................... 19
Le châssis ............................................................................................................. 19
Les roues.............................................................................................................. 19
Le frein................................................................................................................. 20
Le guidon ............................................................................................................ 20
La nacelle ............................................................................................................ 20
Le siège de poussette .......................................................................................... 21
Le siège auto Maxi-Cosi........................................................................................ 25
Introduction
·An de pouvoir utiliser ce produit de manière optimale, nous vous
conseillons de l’utiliser avec soin et de bien l’entretenir. Lisez ce mode
d’emploi attentivement avant d’utiliser la poussette, puis conservez-le
pour vous y rapporter ultérieurement.
·Si vous avez des questions, des remarques, des problèmes ou des récla-
mations, prenez contact avec votre vendeur.
·Si vous souhaitez connaître les accessoires disponibles pour ce produit,
ou être informé des nouveaux produits Mutsy, visitez www.mutsy.com.
⚠AVERTISSEMENT
général
·AVERTISSEMENT : Lisez attentivement ce mode d’emploi, puis rangez-le dans un
endroit sûr pour vous y rapporter ultérieurement. Le non-respect des consignes de ce
mode d’emploi peut avoir des conséquences graves pour la sécurité de votre enfant.
·AVERTISSEMENT : Vous êtes personnellement responsable de la sécurité de votre
enfant. Ne laissez jamais votre enfant sans surveillance.
·AVERTISSEMENT : Évitez les blessures graves dues aux chutes ou glissades. Utilisez
toujours le harnais de sécurité à cinq points.
·AVERTISSEMENT : Avant toute utilisation de la poussette, vériez le dépliage et le
verrouillage corrects et complets du châssis (y compris du guidon).
·AVERTISSEMENT : Avant toute utilisation, vériez que les dispositifs de xation du
landau, du siège ou du siège auto sont correctement bloqués.
·AVERTISSEMENT : Ne laissez pas votre enfant jouer avec ce produit.
·AVERTISSEMENT :Ne laissezpas votreenfant sanssurveillance,ça peutêtredangereux.